User manual PANASONIC VV2017W

[. . . ] Please contact your local authority for further details of your nearest designated collection point. Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation. Operating Instructions LCD Television Model No. VV2017W For business users in the European Union If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information. Information on Disposal in other Countries outside the European Union This symbol is only valid in the European Union. If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal. INPUT MULTI WINDOW OPTION SD CARD EXIT RETURN F. P. TV Customer's Record The model number and serial number of this product may be found on its rear panel. You should note this serial number in the space provided below and retain this book, plus your purchase receipt, as a permanent record of your purchase to aid in identification in the event of theft or loss, and for Warranty Service purposes. [. . . ] 22) · "Auto Setup" will automatically start. 10) · 24 Note Setting "Shipping Condition" (p. 25) erases the PIN number and all settings. 25 Input Labels For easier identification and selection of the input mode, you can label each input terminals or skip terminal that is not connected to any equipment. 14) Displaying PC Screen on TV The screen of the PC connected to the TV can be displayed on the TV. You can also listen to PC sound with the audio cable connected. 34) INPUT 1 INPUT OPTION SD CARD EXIT Display the menu 1 2 Select the external input OPTION SD CARD EXIT Select "PC" Input Selection access RETURN 2 3 Select "Setup" Main Menu VIERA Link Picture Sound Setup RETURN access select AV1 AV2/AV2S AV3/AV3S COMPONENT PC HDMI1 HDMI2 HDMI3 TV select · · Corresponding signals (p. 39) If "H-freq. " or "V-freq. " is shown in red, the signals may not be supported. · Displaying PC Screen on TV Input Labels To return to TV Select "Input Labels" Setup Menu 1/2 access PC menu setting (changed as desired) · Q-Link Settings Child Lock Tuning Menu Off Timer Language Teletext Shipping Condition Input Labels Banner Display Timeout Off FLOF Access 3 seconds select · Menu Picture To make settings "How to Use Menu Functions" to (p. 18) Item R-Gain Adjustments / Configurations (options) Adjusts the white balance for red areas Adjusts the white balance for green areas Adjusts the white balance for blue areas (2. 0 / 2. 2 / 2. 5) Advanced G-Gain PC Settings B-Gain Gamma Input Resolution Clock 4 TV Select a input terminal and set Input Labels 1 of 2 To return to TV EXIT AV1 AV2/AV2S AV3/AV3S COMPONENT PC HDMI1 HDMI2 HDMI3 DVD AV2/AV2S AV3/AV3S COMPONENT PC HDMI1 HDMI2 HDMI3 Set to the minimum level if noise occurs Adjusts horizontal position · · Switches to a wide view VGA (640 × 480 pixels), WVGA (852 × 480 pixels), XGA (1, 024 × 768 pixels), WXGA (1, 366 × 768 pixels) Options change depending on signals Advanced set select H-pos Setup The labels you set will be displayed in "Input Selection" menu (p. If "Skip" is selected, you cannot select the mode. · User input Select "User input" select access PC Setup V-pos Adjusts vertical position You can name each input terminals freely. Set characters User input Clock Phase Store select RETURN · · Eliminates flicker and distortion Adjust after Clock adjustment · Set to the minimum level if noise occurs Name ABCDE UVWXY abcde uvwxy FGHI Z 01 fghi z()+ J 2 j K 3 k . LMNOPQRS 456789!: lmnopqrs *_ T # t Sync set Chooses another synchronous signal if the image is distorted (H & V / On G) H & V : by the horizontal and vertical signals from your PC On G : by the green signal from your PC (if available) (maximum: ten characters) · Other items p. 21 26 27 Viewing from card (Photos) The still images recorded by the digital camera will be displayed. 1 2 INPUT OPTION SD CARD EXIT Insert the SD Card · Warning message for output signal is displayed. · SD Card For details on SD Cards (p. If you turn the TV off during recording from an AV source, the recording will be stopped. · · · · · · · · · · · · · Note HDMI is the world's first complete digital consumer AV interface complying with a non-compression standard. If the external equipment has only a DVI output, connect to the HDMI1 terminal via a DVI to HDMI adapter cable (2). When the DVI to HDMI adapter cable is used, connect the audio cable to the audio input terminal (HDMI1: use COMPONENT-AUDIO terminals). Audio settings can be made on the "HDMI1 Input" menu screen. 20) Applicable audio signal sampling frequencies (2ch L. PCM): 48 kHz, 44. 1 kHz, 32 kHz HDMI2 / 3 terminals are for digital audio signal only. If the connected equipment has an aspect adjustment function, set the aspect ratio to "16:9". These HDMI connectors are "type A". These HDMI connectors are compatible with HDCP (High-Bandwidth Digital Content Protection) copyright protection. An equipment having no digital output terminal may be connected to the input terminal of either "Component", "S-VIDEO", or "Video" to receive analogue signals. The HDMI input terminal can be used with only the following image signals: 480i, 480p, 576i, 576p, 720p, 1080i and 1080p. Match the output setting of the digital equipment. [. . . ] 14). This is a characteristic of liquid crystal panels and is not a problem. The liquid crystal panel is built with very high precision technology giving you fine picture details. Occasionally, a few non-active pixels may appear on the screen as a fixed point of red, green, blue or black. Please note this does not affect the performance of your LCD. Pictures from external equipment are unusual when the equipment is connected via HDMI Is the HDMI cable connected properly? [. . . ]