User manual PANASONIC WJ-220R

[. . . ] This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Caution: To assure continued compliance, (example use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. SA 1966 Power disconnection. [. . . ] DATA Select "7 BIT" or "8 BIT". The default setting is "8 BIT". STOP BIT Select "1 BIT" or "2 BIT". The default setting is "1 BIT". PARITY Select from "NONE", "ODD" or "EVEN". The default setting is "NONE". Notes · Packets will be sent to a network when either setting of "WAITING DATA SIZE TO SEND PACKET" or "WAITING TIMER TO SEND PACKET" is fulfilled. · When "PREFERENCE SETUP" is selected for "DESTINATION SETUP", packets will be set to only one destination. · The encoder cannot receive fragmented UDP packets correctly. · Click the [SET] button to save the changed settings. Otherwise, the changed settings will not be saved. WAITING DATA SIZE TO SEND PACKET (1 - 1024 byte) Enter a desired data length of serial data the RS-485 data port can receive at one time. The entered size will be the maximum size of the packet to be sent to the network. SUBNET MASK Enter the subnet mask of the encoder to connect to the network. When the SW4 switch on the front panel of the encoder is set to ON, a subnet mask assigned by DHCP will be displayed. The default setting is "255. 255. 255. 0". DEFAULT GATEWAY Enter the default gateway to connect to the network. When the SW4 switch on the front panel of the encoder is set to ON, a default gateway assigned by DHCP will be displayed. The default setting is "192. 168. 0. 1". DNS SERVER Enter the IP address of the DNS server to connect to the network. The default setting is "0. 0. 0. 0". MAC ADDRESS The MAC address of the encoder will be displayed. SPEED/DUPLEX Select a transmission speed between the encoder and a network device such as a switching hub or a router from the following. AUTO: Transmission speed will be automatically set. [. . . ] Enter a user name with access level 1 (ADMINISTRATOR) and the password registered to the encoder/decoder to be restarted. Example · Restarting the decoder http://192. 168. 0. 11/cgi-bin/decoder. cgi?com=netvup&submit=RESTART 110 UPDATING Update the firmware of the encoder/decoder by executing the update file transferred to the encoder/decoder in advance. Refer to the page 62 or page 79 to transfer the file to the encoder or the decoder respectively. Format Updating the encoder http://(IP address of the encoder)/cgi-bin/encoder. cgi?com=netvup&submit=START Updating the decoder http://(IP address of the decoder)/cgi-bin/decoder. cgi?com=netvup&submit=START Response HTTP /1. 1 200 OK CR LF CR LF CR LF Cache-Control: no-cache Content-Type: text/plain Content-Length: XX CR LF CR LF (XX: Display the octet number of the Message-Body decimally) Important Notice The user name and the password authentication will be required when trying to update the firmware of the encoder/decoder. Enter a user name with access level 1 (ADMINISTRATOR) and the password registered to the encoder/decoder to be updated. 111 DEFAULT SETTINGS ENCODER Setting Page NETWORK Item IP ADDRESS SUBNET MASK DEFAULT GATEWAY DNS SERVER SPEED/DUPLEX MODE VIDEO&AUDIO ENCRYPTION ENCRYPTION KEY (4 digits: 0 - 9) NTP NTP SERVER HOST/IP ADDRESS INTERVAL TIME ZONE DAYLIGHT SAVINGS DATE [YYYY/MM/DD] DATE [hh:mm:ss] DEVICE NAME LOCATION CONTACT SNMP COMMUNITY START UP COMMAND* DESTINATION IP ADDRESS* MULTICAST IP ADDRESS FOR SETUP* MULTICAST PORT* Default setting 192. 168. 0. 10 255. 255. 255. 0 192. 168. 0. 1 0. 0. 0. 0 AUTO WEB MODE OFF 0000 OFF 24 (GMT-05:00) Eastern Standard Time ON 2003/01/01 00:00:00 WJ-GXE900 public MULTICAST 239. 192. 255. 1 239. 192. 255. 2 51203 SYSTEM VIDEO 239. 192. 10. 1 239. 192. 10. 2 239. 192. 10. 3 239. 192. 10. 4 50000 50000 50000 50000 51000 51000 51000 51000 6. 14 Mbps 6. 14 Mbps 6. 14 Mbps 6. 14 Mbps (150 ms) (150 ms) (150 ms) (150 ms) TOS BIT 0 0 0 0 TTL 16 16 16 16 ENCODER START UP SETUP START START START START CAMERA CABLE COMPENSATION S S S S DYNANIC RANGE NORMAL NORMAL NORMAL NORMAL WATERMARK OFF OFF OFF OFF GOP 15 15 15 15 *: Valid only when "MAIN CPU MODE (MAIN CPU EXISTS)" is selected for "MODE" on the SYSTEM page of the encoder. CAMERA No. CAMERA TITLE (WITHIN 16 CHARACTERS) DESTINATION IP ADDRESS DESTINATION PORT No. [. . . ]