User manual PANASONIC WJ-4600C

[. . . ] Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämä ilmoitus koskee, noudattaa seuraavia standardeja tai muita ohjeellisia asiakirjoja, jotka noudattavat direktiivien 73/23/EEC ja 89/336/EE. Vi erklærer oss alene ansvarlige for at produktet som denne erklæringen gjelder for, er i overensstemmelse med følgende normer eller andre normgivende dokumenter som følger bestemmelsene i direktivene 73/23/EEC og 89/336/EEC. CAUTION: Before attempting to connect or operate this product, please read the label on the bottom. FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY. WARNING: CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN THIS APPARATUS MUST BE EARTHED IMPORTANT The wires in this mains lead are coloured in accordance with the following code. Green-and-yellow: Earth Blue: Neutral Brown: Live As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows. [. . . ] VD2/Cable Compensation Switches (CH1 - CH8) These switches are used to set the most suitable position of the cable-loss compensator and to turn on and off the VD2 (Sync signal) for the cameras connected to the CAMERA IN connectors. Camera Address Switches (CH1 - CH8) These switches are used to set the camera addresses connected to the CAMERA IN connectors. Up to 1 024 addresses can be set in the system. SWITCH PROTEC TOR -4- s Rear View 8 7 6 5 4 3 2 1 VS/VD IN VD VS/VD (THRU) OUT DATA IN DATA OUT CAMERA IN CAMERA OUT 8 7 6 5 4 3 2 1 CODE TERM ON OFF BWS RS485 R GBABAGBABA T T LINE SELECT 2 R 1 21 4 DATA 2 SIGNAL GND 11. Camera Input Connector (CAMERA IN 1 - 8) This connector accepts either a colour or B/W composite video signal from the camera. In addition, the VD2 signal for synchronizing vertical timing of the cameras, and data to control camera site devices are multiplexed through this connector. Camera Output Connector (CAMERA OUT 1 - 8) The video signal connected to the Camera Input Connector (CAMERA IN) is looped through to this connector with an automatic 75 termination. The camera control signal multiplexed on the video signal is not available at this connector. When Power Switch of the Data Converter is turned off, no signal is present at this connector. VD/Through Selector (VD VS/VD (THRU)) This switch is used to choose the output signal of the VS/VD OUT connector. VD: Chooses the internal VD (Vertical Drive) pulse. VS/VD (THRU): Chooses the looping-through sync signals supplied to the VS/VD IN connector from an external device. CH1(SW201): CH3(SW203): CH5(SW205): CH7(SW207): RS485-1(SW221): 1 3 5 7 9 CH2(SW202): 2 CH4(SW204): 4 CH6(SW206): 6 CH8(SW208): 8 RS485-2(SW222): 10 q VD2 and Cable Compensation Setting Set the switches (SW211 to SW218) on the board to choose the most suitable position of the cable-loss compensator and to turn on and off the VD2 (Sync signal) for the cameras. (1) Set the switches to select VD2 On or Off. Note: Select ON for a camera with VD2 capability, otherwise select OFF. (2) Set the switches to select the most suitable cable length as shown below. S: Up to 500 m (1 600 ft) M: 500 m (1 600 ft) to 900 m (2 900 ft) L: 900 m (2 900 ft) to 1 200 m (4 000 ft) (When using RG-6/U (5C-2V) or equivalent cable) Caution: Do not select ON position simultaneously for 3rd and 4th switches. O 1 ON N 3 4 6 7 8 9 2 OFF 5 0 SW201 CH1 O N S M 1 3 2 4 L VD2 Cable Comp Notes: · The camera addresses set should be the same as actual (Real) camera numbers of the AD. · After all address settings are completed restart (Power off then on) the unit to initialize the new settings. Note: Always set 1st switch to OFF position. Initially, the positions shown below are selected at the factory. VD2: Cable Comp: -7ON S 500 m (1 600 ft) s Mounting in the Rack 1. Remove the four rubber feet by removing the four screws from the bottom of the Data Converter. Remove four rubber feet. 2. Place the rack mounting brackets on both sides of the Data Converter and tighten them with the eight supplied screws (M3 X10). 3. Install the Data Converter with the rack mounting brackets in the rack by using four screws (not included). Cautions: · Do not block the ventilation opening or slots on the cover to prevent the appliance from overheating. [. . . ] Select 1 by pressing the Numeric key, then press the AUXILIARY ON key to turn on the housing defroster. To turn off the defroster, select 1 by pressing the Numeric key, then press the AUXILIARY OFF key. Select 2 by pressing the Numeric key, then press the AUXILIARY ON key to turn on the housing wiper. To turn off the wiper, select 2 by pressing the Numeric key, then press the AUXILIARY OFF key. q Auxiliary Control The following function is available only when the WVRC100 or WV-RC150 Receiver is included in the system, and the DIP switch is set to RECV and AUX positions. [. . . ]