User manual PANASONIC WJ-AD550

[. . . ] 3 I Precaution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 I Cautions about the Network Environment . . . . . . . . . . 3 I Limitation of Liability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 I Disclaimer of Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Following are the sample data for matrix controller devices: ID 1 I/F 1 IPA 172. 18. 0. 100 Boot 15010426. sr MXCONT 1-128 MXOSD 1-128 MXSW Input 1-256 Output 1-32 MXALM ­ LCPU Address SW12 SW10 SW9 0 2 0 G SX650 Switch Node SX650 switch node consists of one more WJ-SX650 matrix switcher with WJ-PB65E01 network board. SX650 switch node can only be located within a system domain, and cannot cross over multiple domains. Currently, the system only supports up to one SX650 switch node in a single system domain, and node ID is always set to its domain ID by the system software. G SX650 Switch Node and its Domain In case of a single domain system, all the WJ-SX650 matrix switcher with WJ-PB65E01 network board will be assigned to that domain. In case of a multiple domain system, the system designer has to decide which domain all the WJ-SX650 matrix switcher with WJ-PB65E01 network board should belong to. G Enter SX650 SUBNODES in the WJ-AD550 Admin Console After deciding the domain ID for each WJ-SX650 matrix switcher, the next step is to enter the information in the WJ-AD550 Admin Console for the domain. In the WJ-AD550 Admin Console, SX650 SUBNODES screen, we need to configure the devices. Since these devices are part of the SX650 node, select SX650 from the Switch Nodes command on the Domain menu. Following are the sample data for WJ-SX650 matrix switcher. SWITCH ID 1 IF 1 IPA 172. 18. 0. 100 BRIDGE CONTROL ­ 1 - 256 OSD Input 1 - 32 Output ­ 1 - 256 1 - 32 ALARM 5 OFF 6 OFF 7 ON 8 OFF 00. 00. 00. 00. 00. 00 Address [MODE] EA 22 I How to Identify a Video Switch Link G Links between an SX650/SX850 Node and a GX Node In order to pass video from one switch node to another, video links are required. Page 11 gave an example of a system with video links. In general, you can find video links in the following conditions: · From a video decoder device to an SX650/SX850 matrix switch input · From an SX650/SX850 matrix switch output to a video encoder device The above video links can connect two video switch nodes within the same system domain or different system domains. G Links between two SX650/SX850 Switch Nodes In general, you can find video links from a matrix switch output to a matrix switch input. These links must cross two different system domains. G Enter Video Links in the WJ-AD550 Admin Console (Global database) In the WJ-AD550 Admin Console main screen, select Routing on the Domain menu. Then, enter the video link(s) information into the fields provided. When two operators compete for system resources, only the operator with the higher priority gets the resources. I Global Video Switch and Video Routing This function allows operators to switch video from one video source to another, if the permission is granted. For multiple operators competing for the same resource, it only allows the highest priority operator to perform this function. The next highest priority operator gains control when the highest priority operator releases the resource. Here is a sample operation to switch video from local camera number 1 in domain 1, to another camera number 1 in domain 2, on a local monitor number 1. Login to System Controller: Enter 500 for ID and enter 500 for password (Global Operator). Select monitor 1: Enter 1 and press MONITOR key. Select local camera 1: Enter 1 and press CAMERA key. Select global camera 1(Unit2's camera 1): Enter 200001 and press CAMERA key. Note: Format: Unit (Domain) id (2) + Camera number (1). 200001 (Unit 2, Camera 1) (Note that first entry digit must be non-zero, and must not exceed eight digits). Note: Only Global Operator can access foreign domain resources. [. . . ] Delete the ***{ single asterisks below to make this section active. ***{ Enable/Disable Serial Alarms by port ***{ Note: Port 2 is dedicated to redundant communication ***{ if REDUNDANT:YES is selected by front panel ***{ switch. ***{ Format: AlarmPort=<port 1>, <port 2> ***{ port # = use "1" to indicate desired port (only one) ***{ port # = use "0" to indicate ports not desired *AlarmPort=1, 0 } } } } } } } } } } 67 [ALARMTEXTDISPLAY] ***{ This section is optional. It is not required unless ***{ System defaults are not acceptable. [. . . ]