User manual PANASONIC WJ-DA464

[. . . ] Vi deklarerar härmed värt fulla ansvar för att den produkt till vilken denna deklaration hänvisar är i överensstämmelse med standarddokument, eller andra normativa dokument som framställs i EEC-direktiv nr. Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämä ilmoitus koskee, noudattaa seuraavia standardeja tai muita ohjeellisia asiakirjoja, jotka noudattavat direktiivien 73/23/EEC ja 89/336/EE. Vi erklærer oss alene ansvarlige for at produktet som denne erklæringen gjelder for, er i overensstemmelse med følgende normer eller andre normgivende dokumenter som følger bestemmelsene i direktivene 73/23/EEC og 89/336/EEC. Caution: Before attempting to connect or operate this product, please read the label on the bottom. For U. K. FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY. [. . . ] The master unit supplies the calibration signal to the slaves. This is convenient for synchronizing the internal clock with other connected devices. Make certain to connect the IN and OUT terminals correctly. FWD/REW MODE PASSWORD LOCK ALL OPERATION KEYLOCK BUZZER RESET PULSE TIME ADJUSTING SET TIME AUTO ERASING SKIP&PLAY OFF ***** ***** OFF HIGH SLAVE 9:00 OFF 1. Move the cursor to AUTO ERASING with the [v] or [w] button. Select the desired day number with the JogDial. 1DAY: Only today's records of 0:00 onward are protected. Records before 24:00 of yesterday are erased. 2 to 10DAYS: Records before the specified number of days are erased. 14, 30, 45, 60, 90, 120, 150, 180DAYS: Same as above. Notes: · The day number includes today as 1 day, therefore 2DAYS counts today and yesterday in number. · Auto Erasing is implemented at 24:00 mid night. See illustration for each sequence. DISK START DISK END [STOP] [Default] Restart REC DISK START Stop REC Reset [STOP] The default is [STOP]. DISK END DISK START DISK END [CONTINUE] Overwritten automatically DISK START DISK END DISK START DISK END [ALM CONTINUE] Alarm REC only ALM picture DISK START Stop REC DISK END Recording continues from the start of the next recorder's disk Disk #1 DISK START DISK END Disk #2 DISK START DISK END [SERIES] Disk #n (up to #16) DISK END DISK START Disk #3 DISK END DISK START Loop recording if connected in loop Notes on SERIES connection · See page 12 for physical connections. · See SERIES RECORDING in APPENDIX for setup and operating procedures. 25 REC SETUP REC MODE REC RATE REC QUALITY SF- 12H 12. 5FPS 10(1-10) [ON]: Enables the buzzer beep at the disk end (remaining space 0 %). [OFF]: Disables the buzzer beep. DISK END MODE STOP DISK END BUZZER ON JOG/EXT REC REC MODE JOG CLICK SF- 12H q Jog Click Terminal Definition 206 JOG/EXT REC The JOG CLICK terminal on the rear panel is connected with an external switch. The switch is used either to remotely click the JogDial or to implement the preset mode for manual recording. DISPLAY SELECT LCD CONTRAST JOG/EXT REC JOG CLICK EXT REC MODE SF- 12H 1. Move the cursor to DISK END MODE with the up [v] or down [w] button. Rotate the JogDial to select the desired parameter. [STOP]: Stops recording until a mode other than [STOP] is selected. [CONTINUE]: Old data is automatically overwritten from the disk start. [ALM CONTINUE]: Recording is suspended until an alarm occurs. When an alarm occurs, alarm recording overwrites old data from the disk start. [SERIES]: In series connection, new data is recorded from start to end of the next recorder's disk and so forth. [. . . ] To stop recording · If manual operation is selected, press the STOP button on the current unit. · If internal timer is selected, the unit stops recording at the preset END time. The next unit will start recording when the current unit reaches its disk end. Recording ends when the final unit reaches its disk end. [. . . ]