User manual PANASONIC WJ-DC108

[. . . ] Data Converter WJ-DC108AD Before attempting to connect or operate this product, please read these instructions completely ESPAÑOL FRANÇAIS DEUTSCH ENGLISH ENGLISH VERSION We declare under our sole responsibility that the product to which this declaration relates is in conformity with the standards or other normative documents following the provisions of Directives EEC/73/23 and EEC/89/336. Noi dichiariamo sotto nostra esclusiva responsabilità che il prodotto a cui si riferisce la presente dichiarazione risulta conforme ai seguenti standard o altri documenti normativi conformi alle disposizioni delle direttive CEE/73/23 e CEE/89/336. Wij verklaren als enige aansprakelijke, dat het product waarop deze verklaring betrekking heeft, voldoet aan de volgende normen of andere normatieve documenten, overeenkomstig de bepalingen van Richtlijnen 73/23/EEC en 89/336/EEC. Vi erklærer os eneansvarlige for, at dette produkt, som denne deklaration omhandler, er i overensstemmelse med standarder eller andre normative dokumenter i følge bestemmelserne i direktivene 73/23/EEC og 89/336/EEC. Vi deklarerar härmed värt fulla ansvar för att den produkt till vilken denna deklaration hänvisar är i överensstämmelse med standarddokument, eller andra normativa dokument som framställs i EECdirektiv nr. [. . . ] VD/Through Selector (VD VS/VD (THRU)) This switch is used to choose the output signal of the VS/VD OUT connector. VD: Chooses the internal VD (Vertical Drive) pulse. VS/VD (THRU): Chooses the looping-through sync signals supplied to the VS/VD IN connector from an external device. VS/VD Input Connector (VS/VD IN) Either the VS (Video Sync) signal or the VD (Vertical Drive) pulse can be supplied to this connector for synchronizing the system. Notes: · This input may be looped through to the VS/VD Output Connector by setting the VD/Through selector. · When the VD (or VS) signal is supplied to the VS/VD IN connector, set the DIP switch (SW2) on the circuit board to the VD (or VS) position. Initially, CAM position is selected at the factory. 8 CH4 CH3 CH8 CH7 RECV WIP/DEF s DIP Switch Setting (On the Board) Caution: Before disassembling the Data Converter, be sure to turn off the Power Switch of the Data Converter. Remove the six screws on the top panel of the Data Converter as shown below. 6 7 CH2 CH6 4 AUX SW3 CAM 5 6 7 8 CH2 CH1 (Baud Rate) CH SW902: CH1 6 7 OFF OFF 2 3 4 1 2 3 4 5 6 7 8 5 SW3 5. Set the switches (SW3) on the board to choose the camera or receiver command for RS485 cameras when the AUXILIARY key is pressed, and to set the Baud Rate for communication. SW2 2 OFF SW902 1 Initially, CAM position and 19 200 bps position are selected at the factory. WIP/DEF RECV 1 2 3 1 SW952: CH5 2. The DIP switches are located on the board as shown below. 8 2 3 5 OFF 1 4 OFF AUX 8 CAM CH2 CH1 Dat aC WJ- DC SW952 10 8 AD 4 5 6 onve rter 7 2 400 bps OFF 4 800 bps 3. Set the switch (SW2) on the board to match the sync input signal supplied to the VS/VD Input Connector (VS/VD IN), if applicable. Initially, VS position is selected at the factory. Note: 2nd switch is provided as reserve. 1 2 3 9 600 bps 19 200 bps 6. After setting the switches, secure them by tightening the screws shown above. VS VD SW2 2 OFF ON OFF 1 -6- s DIP Switch Setting (On the Front Board) Remove the switch cover by removing the screw on the front panel of the Data Converter shown below to expose the DIP switches. Remove screw POWER ON SWITCH PROTECTER OFF Data Converter WJ-DC AD RS485 Camera Address VD2 Cable Comp Coax. Camera Address q Camera Address Setting Set the switches (SW201 to SW208, SW221 and SW222) on the board to set the address of the camera that is connected to the Camera Input Connector (CAMERA IN) and RS485 Terminal. Up to 1 024 addresses can be set in the system. Refer to the Camera Address Setting on page 86 for details. Initially, the addresses shown below are selected at the factory. CH1(SW201): CH3(SW203): CH5(SW205): CH7(SW207): RS485-1(SW221): 1 3 5 7 9 CH2(SW202): 2 CH4(SW204): 4 CH6(SW206): 6 CH8(SW208): 8 RS485-2(SW222): 10 q VD2 and Cable Compensation Setting Set the switches (SW211 to SW218) on the board to choose the most suitable position of the cable-loss compensator and to turn on and off the VD2 (Sync signal) for the cameras. (1) Set the switches to select VD2 On or Off. Note: Select ON for a camera with VD2 capability, otherwise select OFF. (2) Set the switches to select the most suitable cable length as shown below. [. . . ] Select the desired camera referring to the Camera Selection. Select 1 by pressing the Numeric key, then press the AUXILIARY ON key to turn on the user's auxiliary 1 switch in the Receiver. To turn off the auxiliary 1 switch, select 1 by pressing the Numeric key, then press the AUXILIARY OFF key. Select 2 by pressing the Numeric key, then press the AUXILIARY ON key to turn on the user's auxiliary 2 switch in the Receiver. . [. . . ]