User manual PANASONIC WJ-FS116

[. . . ] Operating Instructions Model No. WJ-FS109 WJ-FS116 DEUTSCH FS POWER ON OFF Video Multiplexer WJ-FS 109 Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. ESPAÑOL FRANÇAIS ENGLISH Video Multiplexer ENGLISH VERSION We declare under our sole responsibility that the product to which this declaration relates is in conformity with the standards or other normative documents following the provisions of Directives EEC/73/23 and EEC/89/336. Noi dichiariamo sotto nostra esclusiva responsabilità che il prodotto a cui si riferisce la presente dichiarazione risulta conforme ai seguenti standard o altri documenti normativi conformi alle disposizioni delle direttive CEE/73/23 e CEE/89/336. Wij verklaren als enige aansprakelijke, dat het product waarop deze verklaring betrekking heeft, voldoet aan de volgende normen of andere normatieve documenten, overeenkomstig de bepalingen van Richtlijnen 73/23/EEC en 89/336/EEC. For Australia THIS APPARATUS MUST BE EARTHED. [. . . ] REC MODE This item lets you select the time interval (field rate) for switching the camera channel of the REC OUT signal. When REC MODE is set to EXT, the timing is controlled by the connected VTR. When 004-255 (INT) is selected, the timing corresponds to the field rate set here. The parameter settings for different VTR models are shown in the ADDENDUM. Move the cursor to the REC MODE parameter. Select a field rate or EXT by pressing the + or ­ button. The initial factory setting is 004 (INT). 004 - 255 (INT): REC OUT signal is switched from one camera channel to another at the field rate specified here. Note: The appropriate field rate may vary depending on the VTR model. Consult the VTR specifications on the field rate. EXT: Switching of the REC OUT signal is controlled by the camera switching signal supplied by the connected VTR. Note: If set to EXT, make sure that the CAMERA SW IN terminal on the rear panel is connected to the Time Lapse VTR. s Sequence Setup Menu WJ-FS116 SETUP ALARM SETUP MONITOR OUTPUT SETUP REC OUTPUT SETUP SEQUENCE SETUP SYSTEM SETUP Move the cursor to SEQUENCE SETUP on the SETUP menu, then press the SET button. The SEQUENCE SETUP menu appears on the monitor screen as shown below. SEQUENCE SETUP AUTO SKIP SEQ SETUP ON 1. AUTO SKIP This item lets you enable or disable the Auto Skip function to skip any steps where no video signal is present. Move the cursor to the AUTO SKIP parameter. Note: The auto skip function is not available when playing back pictures. 2. SEQ SETUP This item lets you program or edit a Spot Sequence. Up to 16 steps can be assigned in the SPOT SEQ SETUP menu shown on next page. The duration of each step is also determined in the SPOT SEQ SETUP menu. The initial factory setting is sequential display of 16 camera pictures. 15 <WJ-FS116> SPOT SEQ SETUP STEP 1 2 3 4 5 6 7 8 CH 1 2 3 4 5 6 7 8 SEC 2S 2S 2S 2S 2S 2S 2S 2S STEP 9 10 11 12 13 14 15 16 CH 9 10 11 12 13 14 15 16 SEC 2S 2S 2S 2S 2S 2S 2S 2S s System Setup Menu WJ-FS116 SETUP ALARM SETUP MONITOR OUTPUT SETUP REC OUTPUT SETUP SEQUENCE SETUP SYSTEM SETUP <WJ-FS109> SPOT SEQ SETUP STEP 1 2 3 4 5 6 7 8 CH 1 2 3 4 5 6 7 8 SEC 2S 2S 2S 2S 2S 2S 2S 2S STEP 9 10 11 12 13 14 15 16 CH 9 -------SEC 2S 0S 0S 0S 0S 0S 0S 0S Move the cursor to SYSTEM SETUP on the SETUP menu, then press the SET button. The SYSTEM SETUP 1/2 menu appears on the monitor screen as shown below. SYSTEM SETUP TITLE SETUP TITLE POSI CAM SW LOSS PLAYBACK AUTO PASSWORD PWR ON MODE VTR KEY LOCK 1/2 ON ON OFF 1 OFF Step Assignment 1. Move the cursor to the step number you want to edit in the CH area by pressing the cursor (C, D, A, B) buttons. [. . . ] Group Mode The pictures of channels assigned to an ALARM group are recorded with more fields than normal. Assignments are specified in the ALARM SETUP menu. q Monitor Output q WJ-FS116/WJ-FS109 Multiplexer 1. Front Panel Display When an alarm is activated, the Alarm Indicator (Red) and the corresponding Camera Selection Button (Green) blink. The Alarm Output signal is supplied to pin 9 of the ALARM/REMOTE connector for the programmed duration. [. . . ]