User manual PANASONIC WJ-FS616C

[. . . ] Video Multiplexer Operating Instructions Model No. WJ-FS616C LOCK ALARM MULTI MULTI SCREEN SCREEN SELECT 1 CAMERA/PRE SET POSITION 2 3 4 POWER PUSH OPEN RESET SPOT SEQUENCET 5 6 7 ON OFF VCR CAM 9 10 11 8 12 13 14 15 16 Digital Video Mul tiplexer WJ-FS6 16C Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. Caution: Before attempting to connect or operate this product, please read the label on the bottom. For U. S. A CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. [. . . ] Press the [FUNCTION] button to display the next page of the table. The table shown in the figure appears on the monitor screen. SEQ1(SPOT-SEQUENCE)SETUP 2 OF 2 Auto Skip 1. Move the cursor to the AUTO SKIP parameter. Note: The auto skip function is not available when playing back videotape images. Move the cursor to the CAM column you want to edit for the step number by pressing the C, D, A or B button. Select the desired camera or playback channel in the CAM column by pressing the - or + button. 1 - 16: Camera Channel P1 - P16: Playback Channel ­: Not Assigned Notes: · Pressing the Camera Number button assigns the camera channel directly. · Any playback steps programmed in a sequence are excluded from display on the spot monitor and multiscreen 2 monitor due to the way the system is designed. Repeat steps 1 and 2 above to assign other steps. Move the cursor to the PRE column you want to edit for the step number by pressing the C, D, A or B button. STEP CAM PRE TIME 17 - 2SEC 18 - 2SEC 19 - 2SEC 20 - 2SEC 21 - 2SEC 22 - 2SEC 23 - 2SEC 24 - 2SEC STEP CAM PRE TIME 25 - 2SEC 26 - 2SEC 27 - 2SEC 28 - 2SEC 29 - 2SEC 30 - 2SEC 31 - 2SEC 32 - 2SEC 2. Program the sequence pattern for steps 17 to 32 as described previously. Press the [FUNCTION] button to display the previous page of the table. 38 4. After finishing the settings, press the [SET UP/ESC] button to execute the settings and return to the previous SYSTEM SETUP menu. Camera/Playback This item lets you select the camera or playback image to be displayed at each step. Move the cursor to the STEP parameter by pressing the C or D button. Select either CAM or PLAY by pressing the A or B button. PLAY: Enables display of playback image. Move the cursor to the DWELL TIME parameter by pressing the C or D button. Select the desired dwell time by pressing the A or B button. Dwell Time can be selected between 0SEC and 30SEC. Note: If 0SEC is selected for the dwell time, the step will not be displayed on the multiscreen monitor. Move the cursor to the CAM column you want to edit for the area number by pressing the C, D, A or B button. Select the desired camera or playback channel in the CAM column by pressing the - or + button. q Multi Sequence (SEQ2, SEQ3) This item lets you program or edit a Multi Sequence. [. . . ] Also refer to the command table shown later. Code ASCII [STX] [Address] [;] [Transmission Command] [ETX] (02H) ( )­­­­­­­­­­­­­­­­­( ) (03H) A transmission message consists of [STX], [Address], [;], [Transmission Command], and [ETX]. [Address] is expressed as "ADuu, "where `uu' is in the range of "00" through "16" in decimal form to identify the unit number of the Video Multiplexer. When using the RS-232C port to communicate with the PC, [Address] and [;] can be omitted. 2. [. . . ]