User manual PANASONIC WJ-GXE900

[. . . ] MPEG2 Encoder Model No. WJ-GXE900 WJ-GXD900 MPEG2 Decoder Model No. Operating Instructions WJ-GXE900 OPERATE STATUS 1 2 3 4 5 6 7 8 MPEG2 Enc oder WJ-GX E9 900 00 OPERATE LINK1 100 1000 ACT STATUS 1 2 3 4 5 6 7 8 OPERATE MPEG2 Dec LINK1 100 1000 ACT STATUS 1 2 3 4 oder WJ-GX D9 900 00 5 6 7 8 WJ-GXD900 MPEG2 Dec oder WJ-GX D9 900 00 Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. ENGLISH VERSION Caution: Before attempting to connect or operate this product, please read the label on the bottom. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN For U. S. A CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. SA 1965 The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. [. . . ] 1 to 1 000 (ms) are available for "WAITING TIMER TO SEND PACKET" (10 ms intervals). The default setting is "100". 54 NETWORK PORT SETUP DESTINATION SETUP Perform the settings for the destination which receives the packets. Select "DESTINATION IP ADDRESS IN RECEIVING PACKET" or "REFERENCE SETUP (FOLLOWINGS)". DESTINATION IP ADDRESS IN RECEIVING PACKET Serial data will be sent to the IP address contained in the received packet. Therefore, the destination IP address will not be decided until receiving the packet, and it is impossible to send the received serial data from the RS-485 data port to the network. It is useful to select this when receiving packets from several sources and you are required to respond to them. When receiving packets from several sources, the source IP address of the newest packet will be the destination IP address. REFERENCE SETUP (FOLLOWINGS) When selecting this, enter an IP address and a port number for "DESTINATION IP ADDRESS" and "DESTINATION PORT No. " respectively. Serial data will be sent using the entered port number for "DESTINATION PORT No. " to the entered IP address for "DESTINATION IP ADDRESS". DESTINATION IP ADDRESS When "REFERENCE SETUP (FOLLOWINGS)" is selected, enter the IP address of the device on the network to which packets are to be sent. This setting is valid only when "REFERENCE SETUP (FOLLOWINGS)" is selected The default setting is "0. 0. 0. 0". When "REFERENCE SETUP (FOLLOWINGS)" is selected, enter the port number of the device on the network to which packets are to be sent. When "REFERENCE SETUP (FOLLOWINGS)" is selected, enter the port number which receives packets from the network. The default setting is "52000". The default setting is "DESTINATION IP ADDRESS IN RECEIVING PACKET". 55 SETTINGS MENUS OF THE ENCODER NETWORK page Item Descriptions Perform the following settings after referring to a network administrator about the setting items. Perform the settings only when the SW4 switch on the front panel of the encoder is set to OFF. IP ADDRESS Enter the IP address of the encoder. When the SW4 switch on the front panel of the encoder is set to ON, an IP address assigned by DHCP will be displayed. The default setting is "192. 168. 0. 10". SUBNET MASK Enter the subnet mask of the encoder to connect to the network. When the SW4 switch on the front panel of the encoder is set to ON, a subnet mask assigned by DHCP will be displayed. The default setting is "255. 255. 255. 0". [. . . ] BIT RATE CH1 1 1 CH2 2 2 CH3 3 3 CH4 4 4 112 Setting Page AUDIO ALARM-DRY CONTACT Item SETUP Default setting OFF OFF OFF OFF MAKE-CONTACT CAMERA PRESET No. (1 - 64) BIT RATE RESET/TIMER (SEC) 1 - 60, 90, 120, 150, 180, 240, 300 - 3600: 60SEC INTERVAL ALARM-CAMERA SITE ON/OFF CAMERA PRESET No. (1 - 64) BIT RATE RESET/TIMER (SEC) 2 - 60, 90, 120, 150, 180, 240, 300 - 3600: 60SEC INTERVAL ALARM-VIDEO LOSS No. 1 No. 2 No. 3 No. 4 CLOSE CLOSE CLOSE CLOSE Blank for all the camera input channels (No preset control) Refer to "The bit rate when the encoder detects an alarm (both the dry contact and camera site alarm)" on the next page. [. . . ]