User manual PANASONIC WJ-HD200

[. . . ] Digital Disk Recorder Operating Instructions Model No. WJ-HD200 ENGLISH OPERAT E ALARM TIMER SUSPEN D REMOTE RESET LOCK DST SPOT MULTI CAMERA SELECT OSD 1 SEQUEC E 2 6 3 7 HDD 4 8 MULTISCR EEN SELECT FULL ERROR ZOOM 5 SETU /ESC P STOP PLAY REC REC STO P ALARM SERCH TIME&D ATE SEARCH PLAY MOD E SERECT ALARM RECALL PUSH­ PAUSE SET Digital Dis k Recorde r WJ-HD2 00 Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. FRANÇAIS ENGLISH VERSION Caution: Before attempting to connect or operate this product, please read the label on the bottom. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. For U. S. A SA 1965 The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. [. . . ] Note: Assign an address except 1 to WJ-HD200 when using a system controller in the system. G Data Bit (DATA BIT) 1. Move the cursor to DATA BIT with the [D] or [C] button. 7: 7 bits* ; select when using RS-232C protocol. 8: 8 bits G Parity Check (PARITY CHECK) 1. Move the cursor to PARITY CHECK with the [D] or [C] button. NONE: No parity check EVEN: Even parity ODD: Odd parity* G System Unit Address (SYS-UNIT ADDRESS) (exclusive to PS · DATA) When the recorder performs as a system unit, the unit address can be set from the setup menu on the monitor. Move the cursor to SYS-UNIT ADDRESS with the [D] or [C] button. The default value is 1. G Stop Bit (STOP BIT) 1. Move the cursor to STOP BIT with the [D] or [C] button. Select the number of stop bits with the JogDial. 1: 1 bit* 2: 2 bits Assignable address: From 1 to 99, must be unique in the chain. G Alarm Data (ALARM DATA) (exclusive to PS · DATA) The recorder pauses before sending a notice to the connected system controller when an alarm operates. Move the cursor to ALARM DATA with the [D] or [C] button. Select the parameter with the JogDial, and press the JogDial. OFF: Select this when no system controller is connected. 5S: Pauses 5 seconds. G Wait Time (WAIT TIME) The unit retransmits data after waiting the specified time if there is no response from the connected device. Move the cursor to WAIT TIME with the [D] or [C] button. Select the waiting time with the JogDial. The default is OFF. 37 G Camera Number Setup (CAM NO. SETUP) (exclusive to PS · DATA) Camera numbers will be used in a PS·DATA chain when you select a camera to control it from a system controller. SETUPO with the [D] or [C] button, and press the JogDial. SETUP menu opens. I Network Setup (NETWORK SETUP) NETWORK SETUP LINE SPEED AUTO HTTP PORT 00080 DHCP OFF IP ADDR 192. 168. 000. 010 NETMASK 255. 255. 255. 000 GATEWAY 192. 168. 000. 001 CAM NO. SETUP CAM-PORT 1 2 3 4 5 6 7 8 CAM NO. 001 002 003 004 005 006 007 008 Note: The system will restart after the menu setup window is closed when any parameter in this window has been changed. G Line Speed (LINE SPEED) 2. [. . . ] FF: Changes the forward-playback speed by clicking. PREV FRAME: Pauses after returning a frame. NEXT FRAME: Pauses after forwarding a frame. 2. Double-click the file to expand it to the following. [. . . ]