User manual PANASONIC WJ-HDB501

[. . . ] This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Caution: To assure continued compliance, (example use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. SA 1966 Power disconnection. [. . . ] 4800: 4 800 bps 9600: 9 600 bps* 19200: 19 200 bps OFF: Retransmission is disabled. * 100MS: 100 m seconds 200MS: 200 m seconds 1S: 1 second G Control Unit Address (CTL-UNIT ADDRESS) (only for PS ·DATA) When the recorder performs as a controller in the system, the unit address can be set from the setup menu on the monitor. Move the cursor to CTL-UNIT ADDRESS with the [D] or [C] button. Assignable address: From 1 to 99, must be unique in the chain. Note: Assign an address except 1 to WJ-HDB501 when using a system controller in the system. G Data Bit (DATA BIT) 1. Move the cursor to DATA BIT with the [D] or [C] button. 7: 7 bits* ; select when using RS-232C protocol. 8: 8 bits G Parity Check (PARITY CHECK) 1. Move the cursor to PARITY CHECK with the [D] or [C] button. NONE: No parity check EVEN: Even parity ODD: Odd parity* G System Unit Address (SYS-UNIT ADDRESS) (exclusive to PS · DATA) When the recorder performs as a system unit, the unit address can be set from the setup menu on the monitor. Move the cursor to SYS-UNIT ADDRESS with the [D] or [C] button. AUTO: The speed is automatically selected. 100M_FULL: 100 mega byte, full duplex 100M_HALF: 100 mega byte, half duplex 10M_FULL: 10 mega byte, full duplex 100M_HALF: 10 mega byte, half duplex G HTTP Port (HTTP PORT) Set an HTTP port number. Available port numbers: From 00000 to 65535, except the "well-known port" numbers assigned by IANA (Internet Assigned Numbers Authority) G Dynamic Host Configuration Protocol (DHCP) Dynamic Host Configuration Protocol is enabled or disabled. Note: When ON is selected, you cannot enter the IP address, netmask, or gateway. The given parameters will be displayed after getting the IP address from the DHCP server. 38 G IP Address (IP ADDR) The default is "192. 168. 000. 010". G Sequence Setup (SEQUENCE SETUP) SEQUENCE SETUP MULTI SEQ SETUPO SEQUENCE TIMING INT AUTO SKIP ON SPOT SEQ SETUPO SEQUENCE TIMING AUTO SKIP INT ON G Netmask (NETMASK) The default is "255. 255. 255. 000". G Gateway (GATEWAY) The default is "192. 168. 000. 001". I Switcher Setup (SWITCHER SETUP) SWITCHER SETUP START DISPLAY QUAD-4A MULTI SEL MODE ALL SEQUENCE SETUPO CAMERA VIEW SETUPO 1. Move the cursor to SEQ SETUP in the SWITCHER SETUP menu, and press the JogDial. Select either MULTI SEQ SETUP or SPOT SEQ SETUP with the [D] or [C] button, and press the JogDial. The selected menu opens. G Multiscreen Sequence Setup (MULTI SEQ SETUP) Open the QUAD SEQ SETUP menu to program the sequence steps for displaying quad-split and single input images. MULTI SEQ SETUP Video switcher functions are programmed in this menu setup. G Start Display (START DISPLAY) The image in the selected form will be displayed on the monitor when the recorder is turned on. Single image: CH 1 to CH 8 Quad image: QUAD-4A (including 1-4), QUAD-4B (including 5-8) Multi image: 9SCREEN (including 1-8) Sequence: SPOT SEQ, MULTI SEQ STEP 1 2 3 4 5 6 7 8 CAM QUAD-4A QUAD-4B - SEC 2S 2S 2S 2S 2S 2S 2S 2S 1. Move the cursor to the desired step using the [D] or [C] button. Select a camera number with the JogDial, and press the JogDial. [. . . ] SKIP: Jumps the number of the thumbnails. Frame No. : Indicates the frame number of the displayed image. REW: Changes the reverse-playback speed by clicking. PLAY: Starts playing back in ascending order of the file name. [. . . ]