User manual PANASONIC WJ-MP204C

[. . . ] Data Multiplex Unit Operating Instructions Model No. WJ-MP204C ALARM ALARM D SUSPEN POW ON OFF ER Data M ultiplex Unit WJ- MP204 C Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. ENGLISH VERSION Caution: Before attempting to connect or operate this product, please read the label on the bottom. For U. S. A CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. [. . . ] Connections and switch settings are complete. Switch on the power of the connected system devices including the monitor that displays the menus. When setting at the camera site, remove the front cover from the unit to make access possible to the buttons on the front panel. When setting with use of a WV-CU360C System Controller, confirm that the OPERATE indicator is lit on the Controller, meaning that the unit is ready for operation. WJ-MP204C SETUP MENUX. XX COMMUNICATION SYSTEM On the window, you can select and enter the parameter using buttons. A sub menu will open when a line having a [return ] mark at its end is selected. UNIT 901 23 ALARM RESET SUSPEND SET UP SET ESC 3 4 ALARM ALARM SUSPEND 78 q Buttons used in the setup The following buttons are used in the setup. Operations on the following pages are explained on the assumption that the front panel buttons on the WJ-MP204C are used. Check below which WJ-MP204C front panel buttons are equivalent to the buttons on the WV-CU360C. · Data Multiplex Unit WJ-MP204C [C] button: Moves the cursor downward. [SET]: Validates the selected parameter, or opens a sub menu when [ ] appears. [ESC]: Returns the menu to a higher layer. · System Controller WV-CU360C OPERATE SHIFT ALM RESET ALM SUSPEND ALM RECALL VCR CAM MULTI SCREEN SELECT STILL SEQ PAUSE SLOW q To open or close the setup menu 1. Hold down the SETUP/ESC button on the front panel for 2 seconds. Image display will change to the menu window on the monitor, or vice versa. When using a WV-CU360C, hold down the SETUP button on the controller for 2 seconds. The setup menu will open or close. 19 456 1 2 Data Multiplex Unit WJ-MP204C LOGIN ALARM MONITOR UNIT CAMERA BUSY PROHIBITED System Controller WV-CU PROGRAM SETUP CAM SETUP CLOSE FUNCTION CAM FUNCTION AUTO UNIT A NEAR B/W DEF UNIT B AUX 2 EL-ZOOM WIPER WIDE ZOOM TELE UNIT AUTO FOCUS L IRIS RESET FOCUS FAR IRIS OPEN UP 360C R DOWN ­ + SEQUENCE AUX 1 PATROL PLAY MON CAM HOME/PRESET PATROL STOP PATROL LEARN ESC LOGOUT SET PROGRAM PRESET UP L R L R : Moves the cursor up and down. DOWN STILL EL-ZOOM ­ + CAM : Increases or decreases the parameter value. : Validates the selected parameter, or opens a sub menu when [ ] appears. : Returns the menu to a higher layer. SET MON ESC q Setup menus There are two setup menu groups depending on the communication protocol used in the system, menus for PS · Data and for the Camera Communication Protocol. MODE DIP switch # 3 on the rear of the unit is set to the position of the used protocol, and it specifies what menu group is displayed on the monitor. Menu trees are shown below for two protocols. q Setup menus for PS · Data q Setup menus for Camera Communication Protocol COMMUNICATION CAM ADDRESS CAM ADDRESS BAUD RATE DATA BIT PARITY CHECK STOP BIT WAIT TIME COMMUNICATION UNIT ADDRESS BAUD RATE DATA BIT PARITY CHECK STOP BIT WAIT TIME SYSTEM ALARM MODE MONITOR SPOT MONITOR SPOT ALARM DISPLAY SITE ALARM TERM. ALARM ALARM OUTPUT ALARM DATA COMP/VD2/DATA CAMERA IN COMP VD2 DATA VS/VD INPUT CAMERA CONFIG CAMERA CONFIG DAISY MODE TERMINAL DELAY TIME XON/XOFF SYSTEM ALARM MODE MONITOR SPOT ALARM DISPLAY SITE ALARM TERM. ALARM ALARM OUTPUT ALARM DATA COMP/VD2/DATA CAMERA IN COMP VD2 DATA VS/VD INPUT DAISY MODE TERMINAL 20 s Setup Menus for PS · Data q Communication setup (PS · Data) Communication parameters for a PS · Data protocol system are set in this menu. Hold down the SETUP button for 2 seconds to open the setup menu. DATA BIT 1. [. . . ] The alarm activation is informed to the connected peripherals via the DATA terminal or ALARM/REMOTE terminal when the terminal is set to the alarm output mode. Output duration is specified with the ALARM OUTPUT setup. · Digital Disk Recorder enters a specific recording mode. · Video Multiplexer changes pick-up frame rate and frame order. [. . . ]