User manual PANASONIC WJ-MP404

[. . . ] The fact that the equipment operates satisfactorily does not imply that the power point is earthed and that the installation is completely safe. For your safety, if in any doubt about the effective earthing of the power point, consult a qualified electrician. CAUTION: Before attempting to connect or operate this product, please read the label on the bottom. For U. K. FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY. This appliance is supplied with a moulded three pin mains plug for your safety and convenience. [. . . ] Note: When QUAD-A, QUAD-B, or 3x3 is displayed on the monitor screen, the multi picture is skipped only when no camera is connected to all of the channels. ON: When video loss is detected, the picture switches to the quad format. The message "CHXX LOSS" appears on the monitor screen and the alarm buzzer starts beeping. OFF: The video loss alarm is ignored. 3-1-5. Zoom Setting (ZOOM SETUP) The ZOOM SETUP menu lets you set the following items: · ZOOM POSITION · ZOOM TITLE 1 1. Move the cursor to ZOOM SETUP. 1 ** SYSTEM SETUP ** 2 d 3 BORDER VTR OUT * AUTO SKIP VIDEO LOSS ZOOM SETUP * START SCREEN PLAY TITLE STILL-SEL TITLE WHITE OFF OFF 3x3 ON ON 3 2. Press one of the SELECT buttons (+ or -). The ZOOM SETUP menu appears on the monitor screen. Zooming Position (ZOOM POSITION) This parameter lets you select whether to display the zoomed picture in fixed area or variable when the playback multi picture (quad or 3x3) is monitored. Move the cursor to ZOOM POSITION parameter. ** ZOOM SETUP ** ZOOM POSITION ZOOM TITLE QUADRANT ON -9- 2. QUADRANT: When the playback multi picture (QUAD-A, QUAD-B, or 3x3) is monitored, pressing a desired VIDEO SELECT (1, 2, 3, or 4) button switches the currently monitored multi picture to twofold zoomed picture of the selected fixed area. Note: Moving the position of the title is not available. -10- 3-1-8. Still Mode Selected Channel Title (STILL-SEL TITLE) This parameter lets you enable or disable "STILL?" display on the monitor screen when the the still mode is activating. Move the cursor to the STILL-SEL TITLE parameter. 3-3. ALARM OUT This parameter lets you select the duration the alarm signal is output. Select the desired duration the alarm signal is output. 1-30 SEC, 1-5 MIN: The alarm signal is output for the duration you set. ** SYSTEM SETUP ** BORDER VTR OUT * AUTO SKIP VIDEO LOSS ZOOM SETUP * START SCREEN PLAY TITLE STILL-SEL TITLE WHITE OFF OFF 3x3 ON ON ** MAIN** SYSTEM SETUP * ALARM BUZZER ALARM OUT ALARM AUTO RESET SEQ SETUP * TITLE SETUP * CH SETUP * 2SEC 2SEC OFF 2. OFF: "STILL?" is not displayed. Note: Moving the position of the title is not available. 1SEC. . . . . . 30SEC 1MIN. . . . . . 5MIN 3-2. ALARM BUZZER This parameter lets you select the beeping duration of alarm buzzer when alarm is activated. 1-30 SEC, 1-5 MIN: The buzzer keeps on beeping for the duration you set. EXT: The alarm buzzer keeps on beeping until the alarm recover signal is received from an external equipment, such as a VTR. 3-4. [. . . ] · Connect the VTR OUT connector of this unit to the input connector of the VTR. · Connect the VIDEO OUT connector of this unit to the input connector of the monitor. · Connect the wires of the alarm sensors to the alarm input pins of ALARM/REMOTE connector. -24- · Connection with the Alarm Output Connector Power capacity of alarm output connector less than 100 mA: · Make sure to match the polarity when connecting the buzzer to the alarm output connector. · Connect the positive pole (+) of the buzzer to pin 11 of the alarm output connector. Power capacity of alarm output connector more than 100 mA: · Connect the buzzer through a relay circuit to pin 11 of the alarm output connector. [. . . ]