User manual PANASONIC WJ-MS488

[. . . ] Quad Unit WJ-MS488 Before attempting to connect or operate this product, please read these instructions completely For Australia THIS APPARATUS MUST BE EARTHED. To ensure safe operation the three-pin plug supplied must be inserted only into a standard three-pin power point which is effectively earthed through the normal household wiring. Extension cords used with the equipment must be three-core and be correctly wired to provide connection to earth. Wrongly wired extension cords are a major cause of fatalities. [. . . ] 4 button VARIABLE: When the playback multi picture is monitored, the position to be zoomed is selectable by pressing the CURSOR (C, D, A, B) in C EL-ZOOM mode. Note: This function is available only when the playback multi picture is monitored. Zoom Title (ZOOM TITLE) This parameter lets you enable or disable "ZOOM" display on the monitor screen when zoomed playback picture is monitored. Move the cursor to ZOOM TITLE parameter. Notes: · Moving the position of the title is not available. · When the camera title is displayed upper side of the monitor screen, the zoom title is displayed in the bottom of the right corner of the monitor screen. 2. QUAD-A: The QUAD-A picture is displayed. You can select channels to be displayed for QUADA on the CH SETUP menu. QUAD-B: The QUAD-B picture is displayed. You can select channels to be displayed for QUADB on the CH SETUP menu. 3x3: Nine screen segments (3x3) are displayed. FULL: A full-size single picture is displayed. 1-SEQ: A sequence of a full-size single picture is displayed. 4-SEQ: A sequence of quad pictures is displayed. Note: If you select QUAD-A, QUAD-B, or 3x3 on the START SCREEN menu, set the selected parameter to ON on the VTR OUT menu. When OFF is selected on the VTR OUT menu, the parameter selected on the START SCREEN menu will be automatically changed to ON on the VTR OUT menu. 3-1-7. Play Title (PLAY TITLE) This parameter lets you enable or disable "PLAY" display on the monitor screen when playback picture is monitored. Move the cursor to the PLAY TITLE parameter. ** ZOOM SETUP ** ZOOM POSITION ZOOM TITLE QUADRANT ON ** SYSTEM SETUP ** BORDER VTR OUT * AUTO SKIP VIDEO LOSS ZOOM SETUP * START SCREEN PLAY TITLE STILL-SEL TITLE WHITE OFF OFF 3x3 ON ON ZOOM-PLAY 2. Note: Moving the position of the title is not available. -10- 3-1-8. Still Mode Selected Channel Title (STILL-SEL TITLE) This parameter lets you enable or disable "STILL?" display on the monitor screen when the the still mode is activating. Move the cursor to the STILL-SEL TITLE parameter. 3-3. ALARM OUT This parameter lets you select the duration the alarm signal is output. [. . . ] Do not connect it directly. NO NC To Buzzer C Buzzer +24V NC: Normally Closed Contact NO: Normally Open Contact C: Common Relay · Remote Control You can control the SEQUENCE, PLAY, EL-ZOOM, STILL mode, and the MULTISCREEN/QUAD SHIFT, VIDEO SELECT, and MENU/ESC buttons from a remote controller. Connect ALARM/REMOTE Connector (pin 5) to the ground terminal. These functions are activated by contact with the ground terminal. The assignment of each pin is as follows. Alarm Recover In Alarm Reset Out Multiscreen Select MENU/ESC ALARM/REMOTE Select Play back Alarm Out Ground Ground 13 12 11 10 9 8 7 6 5 ALARM/REMOTE (CH4) ALARM/REMOTE (CH3) ALARM/REMOTE (CH2) ALARM/REMOTE (CH1) 4 3 2 1 25 24 23 22 21 20 19 18 17 16 15 14 Ground Ground Still Sequence Zoom Ground ALARM/REMOTE (CH7) ALARM/REMOTE (CH8) ALARM/REMOTE (CH5) ALARM/REMOTE (CH6) -25- BLOCK DIAGRAM This unit is consisted as below. [. . . ]