User manual PANASONIC WJ-MX12

[. . . ] The fact that the equipment operates satisfactorily does not imply that the power point is earthed and that the installation is completely safe. For your safety, if in any doubt about the effective earthing of the power point, consult a qualified electrician. CAUTION: Before attempting to connect or operate this product, please read the label on the bottom. For U. K. FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY. This appliance is supplied with a moulded three pin mains plug for your safety and convenience. [. . . ] Pressing this button displays the pictures on the monitor screen in the sequential order and with the dwell time set on the SEQ SETUP menu. · ESC button When the setup menu (SYSTEM SETUP, SEQ SETUP, TITLE SETUP, TITLE SET or TITLE POSI) is displayed on the monitor screen, this button works as the ESC button. Pressing this button returns the current setup menu to the previous setup menu. SWITCH PROTEC TOR 2. Alarm LED (ALARM) This LED flashes while the alarm signal is received. It changes to steady light when the alarm is reset automatically. To turn the flashing LED off, press the ALARM RESET/QUAD/SEQ button. Alarm Reset/Quad/Sequence/Escape Button (ALARM RESET/QUAD/SEQ/ESC) This button has different functions in different modes, as described below. · ALARM RESET button When an alarm signal is received, this button works as the ALARM RESET button. Pressing this button in an alarm situation cancels the alarm mode with the following results: 1. The video loss caution message on the monitor screen disappears and the screen returns to the camera picture. -3- 4. VIDEO SELECT (1, 2, 3, 4)/CURSOR (4, 5)/SELECT(­, +) Buttons These buttons select the video signal or move the cursor on the setup menus. · VIDEO SELECT(1, 2, 3, 4) buttons When the setup menu is not displayed, these buttons work as VIDEO SELECT buttons. Press one of the SELECT buttons (­ or +). The SYSTEM SETUP menu appears on the monitor screen. Note: To return to the MAIN menu, press the ESC button. ESC CURSOR ­ SELECT + or ** SYSTEM SETUP ** BORDER VIDEO OUT AUTO SKIP VIDEO LOSS ON QUAD OFF ON ALARM ALARM RESET QUAD/SEQ VIDEO SELECT MENU 1 ESC 2 3 4 ­ CURSOR SELECT + or ** SYSTEM SETUP ** BORDER VIDEO OUT AUTO SKIP VIDEO LOSS ON QUAD OFF ON e Borderline (white) 3-1-1. Border (BORDER) This parameter lets you set the appearance of the borders that divide the screen. ON: The borders appear when QUAD is selected for VIDEO OUT. OFF: The borders do not appear. ALARM RESET QUAD/SEQ VIDEO SELECT 3-1-2. Quad/Sequence (VIDEO OUT) This parameter lets you select the quad picture or sequential single picture for display on the monitor screen. QUAD: The quad picture appears on the monitor that is connected to the VIDEO OUT connector. SEQ: The single picture appears sequentially in the order to set on the of SEQUENCE SETUP submenu of the MAIN menu. ALARM MENU 1 ESC 2 3 4 ­ CURSOR SELECT + or ** SYSTEM SETUP ** BORDER VIDEO OUT AUTO SKIP VIDEO LOSS ON QUAD OFF ON ** SYSTEM SETUP ** BORDER VIDEO OUT AUTO SKIP VIDEO LOSS ON QUAD OFF ON -7- 3-1-3. Auto Channel Skipping (AUTO SKIP) Setting This parameter lets you set automatic skipping of channels to which no camera is connected. 1. Video Loss Checking (VIDEO LOSS) This parameter lets you activate a function that checks whether the video signal is being supplied to the VIDEO INPUT connector. [. . . ] Select the position where the title is to be displayed by pressing the CURSOR buttons (4 or 5). Press the ESC button to return to the previous menu. ** TITLE SETUP ** CAM TITLE TITLE SET * TITLE POSI * ALARM TITLE ON ON ** TITLE SETUP ** CAM TITLE TITLE SET * TITLE POSI * ALARM TITLE ON OFF ALARM 1. . . . . . . Note: All channel titles will be displayed in the same position. You cannot specify a different position for each title. -11- SYSTEM CONNECTIONS SYSTEM 1 The input video signals for this unit are not synchronized. VIDEO VIDEO VIDEO VIDEO WJ-MX12 OUT 4 IN OUT 3 VIDEO IN OUT 2 IN OUT 1 IN VTR OUT VIDEO OUT ALARM/REMOTE SIGNAL GND Monitor Monitor VTR Notes : · When pressing the ALARM RESET/QUAD/SEQ/ECS button or the VIDEO SELECT/CURSOR/SELECT buttons, the picture on the video monitor may roll briefly at the time of switching. · The video signal to be recorded by the VTR should be supplied from the VTR OUT connector of this unit and not from the VIDEO OUT/ESC connector of this unit, unless VTR servo control disturbances are allowable when setting the ALARM RESET/ QUAD/SEQ/ECS button or the VIDEO SELECT/CURSOR/SELECT buttons. [. . . ]