User manual PANASONIC WJ-NDB301

[. . . ] BE LIABLE TO ANY PARTY OR ANY PERSON, EXCEPT FOR REPLACEMENT OR REASONABLE MAINTENANCE OF THE PRODUCT, FOR THE CASES, INCLUDING BUT NOT LIMITED TO BELOW: (1) ANY DAMAGE AND LOSS, INCLUDING WITHOUT LIMITATION, DIRECT OR INDIRECT, SPECIAL, CONSEQUENTIAL OR EXEMPLARY, ARISING OUT OF OR RELATING TO THE PRODUCT; (2) PERSONAL INJURY OR ANY DAMAGE CAUSED BY INAPPROPRIATE USE OR NEGLIGENT OPERATION OF THE USER; (3) UNAUTHORIZED DISASSEMBLE, REPAIR OR MODIFICATION OF THE PRODUCT BY THE USER; (4) ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE, OR LOSS OR DAMAGE, ARISING OUT OF THE SYSTEM COMBINED BY THE DEVICES OF THIRD PARTY. FEATURES The RAID Board WJ-NDB301 is an option for installation into the Network Disk Recorder WJ-ND300. The RAID board enables the network disk recorder to use the RAID 5 function that can recover data even though one of the hard disk drives is failed. RAID level 5 regards 3 or more drives as one drive, and it is possible to read data by attaching error correction data even though one of the drives is broken automatically. [. . . ] Unscrew WJ-ND300 (2 screws from top, 4 screws from sides, and 5 screws from rear) and remove the top cover. Connect between the main and RAID boards with 2 cables that belong to the main board. To main board To RAID board 4. Detach the cable from the cable clamp to unbind it, and pass the cable through the cable clamp as shown in the illustration below. 2. Disconnect all of the HDD cables. Hold the cables using the cable clamp. HDD cables 3 5. (1) Mount the RAID board so that the mounting holes (q to r) of the RAID board are aligned with the mounting holes (q to r) of the main unit (WJND300) respectively by referring the illustration. (1) Use the HDD cable holding clamps attached to the RAID board to bundle two of the HDD cables each disconnected in Step 2. (2) Connect all of the HDD cables and 3 cables to the RAID board. q HDD cable holding clamp Pass the HDD cable for HDD1 (HDD3) through the pull-ring of the cable for HDD2 (HDD4). q r e e r w w (2) Secure the RAID board to the main unit with the screws (6 screws with washer for top of the board, 2 screws for rear of WJ-ND300, and 1 flat-head screw for side of WJ-ND300) attached to the board. 7. Put the top cover back and secure it with the screws removed in Step 1. q y r w e t u o Flat-head screw i 6. The original positions of the HDD cable connectors on the main board of the WJ-ND300 and the positions of the RAID board are as shown in the illustration below (Fig. 1). q w e r r w q e RAID board of the WJ-ND300 4 SETUP · The settings relating to the RAID function can be performed on the setup menu displayed on the LCD on the front panel of the unit. Refer to the Installation Guide for further information. · Refer to the operating instructions of the Network Disk Recorder WJ-ND300 for descriptions of the connections. TROUBLESHOOTING Problem Check item/Remedy · Is the HDD cable connected to the RAID board correctly and firmly?· Is the HDD cable connected to the hard disk drive correctly and firmly?· Is the HDD power cable connected to the hard disk drive correctly and firmly?· Is the provided cable connected correctly and firmly?· Is the jumper setting on the HDD set as the master? The hard disk drive is not recognized. The unit runs in the SINGLE mode. · Set the unit to the RAID5 mode. [. . . ] Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation. For business users in the European Union If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information. Information on Disposal in other Countries outside the European Union This symbol is only valid in the European Union. If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal. 7 For U. S. , Canadian and Puerto Rican fields: Panasonic System Solutions Company, Unit Company of Panasonic Corporation of North America Security Systems www. panasonic. com/security For customer support, call 1. 877. 733. 3689 Executive Office: Three Panasonic Way 2H-2, Secaucus, New Jersey 07094 Zone Office Eastern: Three Panasonic Way, Secaucus, New Jersey 07094 Central: 1707 N. Randal Road, Elgin, IL 60123 Southern: 1225 Northbrook Parkway, Suwanee, GA 30024 Western: 6550 Katella Ave. , Cypress, CA 90630 For the other fields: Matsushita Electric Industrial Co. , Ltd. Osaka, Japan http://www. panasonic. co. jp/global/ Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905)624-5010 http://www. panasonic. ca Panasonic Sales Company Division of Panasonic Puerto Rico Inc. San Gabriel Industrial Park 65th Infantry Ave. [. . . ]