User manual PANASONIC WJ-NT314

[. . . ] Network Interface Unit Network Operating Instructions Model No. WJ-NT314 OPERATE LINK RC V SND Network Interfac e Unit W J-NT31 4 Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. CONTENTS Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 About these operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Trademarks and registered trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Viewer Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Default setting: ON 32 Configures the multi-screen settings [Multi-screen setup] The cameras to be used for the multi-screen display can be registered on this page. The following cameras are available for the multi-screen display. (As of August, 2007) Cameras connected to WJ-NT314, cameras connected to the network, WV-NP240 series, WV-NP1000 series, WV-NW470S series, WV-NP472, WV-NS320 series, WV-NS202, WV-NF284, WV-NS202A, WJ-NT304 [CH No. ] Select a desired channel number (CH1 to 4) when displaying images on a multi-screen using a network device with channel information such as this unit. Select "-" when displaying images on a multi-screen using a device without channel information. Available value: -, 1 - 4 Default setting: [Camera title] Enter the title of the camera. The entered camera title will be displayed on a multi-screen. Number of characters that can be entered: 0 - 20 characters Default setting: (blank) [IP address] Enter the IP address or the host name of the camera to be used for the multi-screen. 4 cameras can be registered as a group and up to 4 groups (16 cameras) can be registered. When the HTTP port number for the camera had been changed, enter as follows: (Example: 192. 168. 0. 10: 8080) Number of characters that can be entered: 1 - 128 characters Default setting: (blank) Notes: · When using the host name, it is necessary to configure the DNS settings of the PC in use. · When displaying images from cameras connected to this unit on a multi-screen, set the IP address of the unit. 33 Configure the AVMD settings [Video analytics setup] The settings relating to the detection area, depth, and schedule for AVMD can be configured on the "Video analytics setup" page. The "Video analytics setup" page has 2 tabs of the [AVMD] tab, and the [Schedule] tab. Set the detection program [AVMD] Click the [AVMD] tab on the "Video analytics setup" page. It is possible to set up to 8 preset positions (CH1 to CH4) for 8 detection programs. It is possible to set intruder detection area (3 types), object abandonment / removal detection area, and an area not to activate AVMD. When editing the detection program, perform the same procedure. Important: The detection program will not be applied to the AVMD function only with setting. To apply the setting, select the detection program for "AVMD" of the [Alarm] tab on the "Alarm setup" page. ( page 40) However, up to 2 channels of CH1 to CH4 are available. Note: When the detection program has already been set, the edited titles will be displayed on the pull-down menu. It is possible to display and change the settings by selecting a title and clicking the [DISPLAY] button. Step 2 Enter the title in "Detection program title". Number of characters that can be entered: 1 - 20 characters When "Detection program title" is blank, the default setting will be applied. Default setting: 1-8 Detection program Step 3 Select the channel to activate the AVMD from "CH No. ". [. . . ] (2) Select "Settings" from "Display Properties", and then click the [Advanced] button. (3) Click the [Troubleshoot] tab and disable the DirectDraw acceleration by adjusting the level of "Hardware acceleration". When displaying MPEG-4 images on two browser windows or more, images from two cameras or more are displayed in sequence on a single browser window. ­ 68 Depending on the OS installed on the PC, the following may occur. Follow the instructions below when the following occurred. [. . . ]