User manual PANASONIC WJ-PB65E01E

[. . . ] · Pay attention to static electricity Make certain to keep boards inside the anti-static sack until it is installed. Put your hand on a metallic surface, other than the boards to discharge static electricity before installation. Do not touch components mounted on the boards directly by hand. Hold only both edges of the boards when installing. References Along with this document, refer to Central Processing Unit WJ-MPU955A Operating Instructions for major operating controls, their functions, and switch settings. Preface Network Board WJ-PB65E01E is designed for the connection with Central Processing Unit WJ-MPU955A and system expansion of Matrix Switcher WJ-SX650 Series. Features · With this board, the network connection between Central Processing Unit WJ-MPU955A and Matrix Switcher WJ-SX650 Series becomes available to expand the system composition. [. . . ] Select "Control Panel" - "Add/Remove Programs". Add/Remove Programs window will be displayed on the PC screen. Select "Firmware version up software". Click "Remove" or "Change/Remove", and follow the directions. Note: If the Firmware update software has already been installed on a PC, installation is impossible. Install the application again after uninstallation. PC: IBM PC/AT Compatible CPU: Intel® Pentium® 3, 500 MHz or faster Memory: 128 MB or more Hard drive space: 30 MB or more for installation of the Firmware update software 50 MB or more for installation of WJ-SX650 Series Initial Setup Tool Note: If Microsoft® . NET Framework 1. 1 has not been installed on the PC, 160 MB or more is required. I PC Connection An RS-232C crossing cable (9-pin D-sub) is used for connection between WJ-SX650 Series and PC. <SERIAL port> (Output rear board) Rear Side of WJ-SX650 Series (WJ-PB65E01 installed) 4 3 2 1 C 3 SIGNAL GND EXTENSION 3 IN EXTENSION 2 IN MODE RS485 (CAMERA) MODE MODE RS485 (CAMERA) MODE IN C-3 2 Monitor: 1 024 x 768 pixels or more, HIGH color 16 bit or more VIDEO OUT 4 32 31 30 VIDEO OUT 3 29 28 27 26 VIDEO OUT 2 25 24 23 VIDEO OUT 1 22 21 20 19 ALARM IN 18 17 IN X-2 RS485(CAMERA) SET UP ON 4-Line MODE ON 4-Line 16 15 14 13 12 11 10 9 CAMERA IN 4 8 7 6 5 4 3 2 1 IN X-1 1 MODE PC 3 2 1 B 3 MODE RS485 (CAMERA) MODE MODE RS485 (CAMERA) MODE IN B-3 2 1 DATA 4 Video Output Board 2 Video Output Board 1 DATA 3 DATA 2 TMNL6 TMNL2 DATA 1 TMNL5 TMNL1/PS DATA TERM. ON ON TERM. OFF 4 3 2 1 OFF OUT EXTENSION 1 IN TERM. ON OUT X-3 A 3 AC IN HDR4/TMNL8 HDR3/TMNL7 HDR2/TMNL4 HDR1/TMNL3 MODE MODE MODE DATA MODE MODE DATA MODE Serial Interface: 9-pin D-sub connector 16 15 14 13 12 11 10 9 MONITOR OUT 8 7 6 5 4 3 2 1 OUT X-2 2 10/100 BASE-T ALARM OUT 2 ALARM OUT 1 VS IN Video Output Board 1 Only VS OUT (THRU) VS OUT SERIAL 1 SIGNAL GND NETWORK OUT X-1 9-pin D-sub (Female) 9-pin D-sub (Female) Cross cable 4 <TEST port> (Output front board) Front side of WJ-SX650 Series (Front panel detached) PC 4. The following message will be displayed. Then, click "OK". RESET No. MODE PULL POWER ON OFF TEST RESET MODE 9-pin D-sub (Female) 9-pin D-sub (Female) 5. "File Selection" window is displayed. Cross cable I Firmware Update Procedure Note: The following is the procedure when using the Windows XP operating system. If you performed wrong operations, the monitor display will return to Step 3. Select "Start" - "All Programs" - "Panasonic" - "Firmware version up software" - "Firmware version up software x. xx". (x. xx is the version number. ) Then, run the program. Firmware update software will start up, and the login window will be displayed on the PC screen. Click "Browse" to select the firmware file of WJ-SX650 Series for update. The file is located in the following directory. E:\PWriter\SX650_vXXXXX_yyyy. mot (E is the CD-ROM drive, "X" is the software version, and "y" is the checksum. ) Note: Make a note of version displayed in the "File Selection" window. The version will be required for checking in Step 7. Connect the SERIAL port of WJ-SX650 Series and PC. (Refer to the illustration of <SERIAL port> in p. 4. ) Then, perform the firmware update by following the instructions given. Enter the user name and password. "Firmware update software" window is displayed. Then, click "WJ-SX650 Series". Notes: · Firmware update procedure is as follows: Current version check Firmware update New version check If the current version is the same as the version you have noted down in Step 5, firmware update is not required. [. . . ] Note: The files specified below are included on the CD-ROM. WJ-SX650 Series Firmware Program Writer (Firmware update tool) WJ-SX650 Series Initial Setup Tool Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households) This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take these products to designated collection points, where they will be accepted on a free of charge basis. Alternatively, in some countries you may be able to return your products to your local retailer upon the purchase of an equivalent new product. [. . . ]