User manual PANASONIC WJ-PB85L32

[. . . ] Vi deklarerar härmed värt fulla ansvar för att den produkt till vilken denna deklaration hänvisar är i överensstämmelse med standarddokument, eller andra normativa dokument som framstölls i Direktiv 73/23/EEC och 89/336/EEC. Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämä ilmoitus koskee, noudattaa seuraavia standardeja tai muita ohjeellisia asiakirjoja, jotka noudattavat direktiivien 73/23/EEC ia 89/336/EEC. Vi erklærer oss alene ansvarlige for at produktet som denne erklæringen gjelder for, er i overensstemmelse med følgende normer eller andre normgivende dokumenter som fælger bestemmelsene i direktiven 73/23/EEC og 89/336/EEC. FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING THIS APPARATUS MUST BE EARTHED IMPORTANT The wires in this mains lead are coloured in accordance with the following code. Green-and-yellow: Earth Blue: Neutral Brown: Live As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows. [. . . ] Press the MON (ESC) button to return to the previous ALARM MODE 3 menu. ALARM MODE MODE3(AL=01) =­­-­­ << M1 S << M5 G M2 S M6 G M3 T M7 G M4 T M8 G >> >> · Tour Sequence Mode · Mode selection on ALARM MODE3 table Move the cursor to the MODE parameter by moving the Joystick Controller. Then set the Mode to SPOT, TOUR or GROUP by pressing the +1CAM INC or ­1CAM DEC button. If TOUR is selected on the above menu, the display will change as follows: ALARM MODE3(AL=01) · Spot Mode 1. If the SPOT is selected on the above menu, the display will change as follows: MODE =TOUR S E Q N O. = 0 1 MONI =3 << M1 S << M5 G M2 S M6 G M3 T M7 G M4 T M8 G >> >> ALARM MODE MONI << M1 S << M5 G MODE3(AL=01) CAM =01 PRE =01 DWELL=10S M3 T M7 G M4 T M8 G >> >> =SPOT = 2 M2 S M6 G 2. Move the cursor to the MONI parameter by moving the Joystick Controller, then enter a Monitor Number (1-8) to run the sequence by pressing the Numeric button or the +1CAM INC or ­1CAM DEC button. Notes: Select a Monitor Number with T (Tour Sequence Mode) that is previously assigned to the Monitor Number area. Monitor Numbers without the T cannot be programmed on this table. parameter by moving the Joystick Controller, then enter a Tour Sequence Number to be run on the selected monitor by pressing the Numeric button or the +1CAM INC or ­1CAM DEC button. Press the MON (ESC) button to return to the previous ALARM MODE 3 menu. 2. Move the cursor to the MONI parameter by moving the Joystick Controller, then enter a Monitor Number to display the spot picture by pressing the Numeric button or the +1CAM INC or ­1CAM DEC button. When satisfied with the programming of schedules on this page, press the HISTORY FWD button to select the next page. Repeat the above procedures until all schedules are programmed. Press the HISTORY BACK button to go back to the previous page. When satisfied with all schedules, press the MON (ESC) button to return to the previous ALARM SCHEDULE menu. Note: The programmed schedules are automatically placed in chronological order. Repeat the above procedures to programme other days. ALARM P R O G. C L E A R = S E T To programme or edit an Alarm Schedule, do the following: 1. DAY parameter by moving the Joystick Controller. Caution: When programming an alarm schedule that extends into the next day, divide the schedules into two separate schedules and programme both schedules separately. For example, Monday 23:00 - 24:00 Tuesday 0:00 - 7:00 -37- s OPERATOR The OPERATOR menu allows access to two items: the level table and operator registration. Select OPERATOR on the SETUP MENU by pressing the Joystick Controller, then press the CAM (SET) button to display the OPERATOR menu as shown below. 1. LEVEL TABLE This table is used to determine what setup functions and operations may be performed by the three (3) operator levels. [. . . ] 32 T05 ON: Active OFF: Not active UNCONTROL: Function is not equipped . . . . . . . : unavailable Possible active modes, as indicated in this table, are defined below. A SP TMM GMM P CAMERA SETUP RECALL STATUS : Alarmed : Spot : Tour Sequence : Group Sequence : Paused Sequence : Camera Setup : System Setup : Alarm Recall Display : System Status Display Note: The sequence number is inversely displayed on the table when a sequence runs in the reverse direction. -61- 17. Priority Lock This function is used to retain control of a monitor for an operator, even after that operator has selected another monitor or has logged out. [. . . ]