User manual PANASONIC WJ-SW208

[. . . ] To ensure safe operation the three-pin plug supplied must be inserted only into a standard three-pin power point which is effectively earthed through the normal household wiring. Extension cords used with the equipment must be three-core and be correctly wired to provide connection to earth. Wrongly wired extension cords are a major cause of fatalities. The fact that the equipment operates satisfactorily does not imply that the power point is earthed and that the installation is completely safe. [. . . ] OFF: Disables display of the subtitle "STILL" on the monitor screen. 13 3. BORDER This item lets you select the colour of the border that splits the camera pictures in a Multiscreen display. Move the cursor to the BORDER parameter. Select the desired mode or colour by pressing the + or ­ button. The initial factory setting for the border colour is WHITE. WHITE: GREY: BLACK: OFF: White Border Grey Border Black Border No Border s Record Output Setup Menu WJ-FS116 SETUP ALARM SETUP MONITOR OUTPUT SETUP REC OUTPUT SETUP SEQUENCE SETUP SYSTEM SETUP 4. QUAD SHIFT This item lets you enable or disable the quad shift operation when the MULTISCREEN SELECT button is pressed on the front panel. Quad shift displays a picture series such as 1-2-3-4 or 5-6-7-8 on quad screens. Move the cursor to the QUAD SHIFT parameter. Select ON or OFF by pressing the + or ­ button. OFF: Disables the quad shift operation. Move the cursor to REC OUTPUT SETUP on the SETUP menu, then press the SET button. Up to 16 steps can be assigned in the SPOT SEQ SETUP menu shown on next page. The duration of each step is also determined in the SPOT SEQ SETUP menu. The initial factory setting is sequential display of 16 camera pictures. 15 <WJ-FS116> SPOT SEQ SETUP STEP 1 2 3 4 5 6 7 8 CH 1 2 3 4 5 6 7 8 SEC 2S 2S 2S 2S 2S 2S 2S 2S STEP 9 10 11 12 13 14 15 16 CH 9 10 11 12 13 14 15 16 SEC 2S 2S 2S 2S 2S 2S 2S 2S s System Setup Menu WJ-FS116 SETUP ALARM SETUP MONITOR OUTPUT SETUP REC OUTPUT SETUP SEQUENCE SETUP SYSTEM SETUP <WJ-SW208> SPOT SEQ SETUP STEP 1 2 3 4 5 6 7 8 CH 1 2 3 4 5 6 7 8 SEC 2S 2S 2S 2S 2S 2S 2S 2S STEP 9 10 11 12 13 14 15 16 CH 9 -------SEC 2S 0S 0S 0S 0S 0S 0S 0S Move the cursor to SYSTEM SETUP on the SETUP menu, then press the SET button. The SYSTEM SETUP 1/2 menu appears on the monitor screen as shown below. SYSTEM SETUP TITLE SETUP TITLE POSI CAM SW LOSS PLAYBACK AUTO PASSWORD PWR ON MODE VTR KEY LOCK 1/2 ON ON OFF 1 OFF Step Assignment 1. Move the cursor to the step number you want to edit in the CH area by pressing the cursor (C, D, A, B) buttons. Select the desired camera channel in the CH area by pressing the Increment (+) or Decrement (­) button. 1 - 16: Camera Channel Note: 10-16 are not available for WJ-SW208. Repeat the above procedures to assign other steps. To go to SYSTEM SETUP 2/2, press the C button. SYSTEM SETUP ENCODE PANA 2/2 SYSTEM SETUP ENCODE SW INTERVAL NO. OF CAMS OTHERS 1 16 2/2 Dwell Time 1. Move the cursor to the SEC (Second) area by pressing the cursor (C, D, A, B) buttons. [. . . ] "CHXX LOSS" is displayed on the monitor screen. q Record Output The pictures of channels where alarm is activated are recorded on the VTR in the mode specified for the ALM REC MODE parameter on the ALARM SETUP menu. 1. Alarm Priority Mode The pictures of channels where alarm is activated are recorded with more fields than in normal recording if ALM PRI is specified in the ALARM SETUP menu. 2. Alarm Only Mode Only the picture of the channel receiving an alarm is recorded while other channels' are ignored. s Alarm Operation When an alarm is activated, the Multiplexer, the Record Output and Monitor Output perform as shown below. Refer to the ALARM SETUP menu of the SETUP MENU on page 11 for settings. 3. [. . . ]