User manual PANASONIC WJ-SX150A

[. . . ] Matrix Switcher Operating Instructions Model No. WJ-SX150A OPERATE OPERAT E IF COO LED WILL BLIN LING FAN K MALFUN CTIONS Matrix Sw itcher WJ -SX 150 A Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. ENGLISH VERSION Caution: Before attempting to connect or operate this product, please read the label on the bottom. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. For U. S. A SA 1965 The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. [. . . ] Notes: If you configure the master-slave composition, settings concerning LCN (logical camera number) and Multiplexer Title (refer to p. When you click on the Save Exit button, a message window will appear to confirm you the change. In WJ-SX150A Administrator Console, camera channels of the Master unit which are connected to MONITOR OUT 1/2/3/4 of Slave units are displayed in gray. You cannot configure the parameters. How to Display CAM 1 to 16 This stands for a camera channel of the unit. Logical Camera Number Click on each drop-down menu to select a desired logical camera number. For camera channels without camera connections, select "- -". (Save Exit) button Saves the configuration and closes the Logical Camera Number window. (Cancel Exit) button Cancels the configuration and closes the Logical Camera Number window. Notes: If logical camera numbers are not selected, the cameras' LCNs are not displayed in each window of SETUP MENU and WJ-SX150A Administrator Console. You can select a logical camera number for only one channel. When you select the same number more than one time, a message will appear. The message will notify you that the number has been already used. If you click on "Yes", the newer will be activated and the older will be changed to "- -". If you click on "No", the changed parameters will return to the former state. If five units (Master and Slave 1 to 5) are connected in the system, you cannot select logical camera numbers for Master. Logical Camera Number This window configures logical camera numbers assigned to camera channels of each unit. During operation, logical camera numbers are used for camera control and monitor display. To display this window, click on the (Logical Camera Number) button in the main window (p. 80). 82 Put a file to SX150A Pressing this button will start the putting of the configuration file from the PC to the unit. Get a Configuration Data from SX150A Pressing this button will start the getting of the configuration data from the unit to the PC. How to Display To display this window, click on the SX150A) button in the main window (p. (Put to How to Display To display this window, click on the SX150A) button in the main window (p. (Get from Parameters The file name of the configuration data appears. (OK) button To put the configuration file from the PC to the unit, click on this button. (Cancel Exit) button To cancel the putting of the configuration file from the PC to the unit, click on this button. Notes: The setup file has been configured at the factory, and the file names appear on the main window's title bar. Put the file from the PC to the unit when the time with no necessary to the continuous system operation, such as after-hours. [. . . ] ER305 ER309 Gateway timeout error Internal error Timeout error has occurred during the gateway communication. The internal processing error has happened. Example: The command is valid but it cannot be executed. (1) The unit receives the zoom command while selecting a camera without electronic zoom function. Transmission Command (ASCII) [STX] CMD:R01ZM [ETX] Transmission Command (ASCII) [STX] ANS:R01ZM:ER301 [ETX] 161 WORKSHEETS Gathering information for the initial configuration and recording on the following worksheets are recommended. [. . . ]