User manual PANASONIC WJ-SX350

[. . . ] Matrix Switcher WJ-SX350 Before attempting to connect or operate this product, please read these instructions completely ESPAÑOL FRANÇAIS DEUTSCH ENGLISH ENGLISH VERSION We declare under our sole responsibility that the product to which this declaration relates is in conformity with the standards or other normative documents following the provisions of Directives EEC/73/23 and EEC/89/336. Noi dichiariamo sotto nostra esclusiva responsabilità che il prodotto a cui si riferisce la presente dichiarazione risulta conforme ai seguenti standard o altri documenti normativi conformi alle disposizioni delle direttive CEE/73/23 e CEE/89/336. Wij verklaren als enige aansprakelijke, dat het product waarop deze verklaring betrekking heeft, voldoet aan de volgende normen of andere normatiefve dokumenten, overeenkomstig de bepalingen van Richtlijnen 73/23/EEC en 89/336/EEC. Vi erklærer os eneansvarlige for, at dette produkt, som denne deklaration omhandler, er i overensstemmelse med den følgende standarder eller andre normative dokumenter i følge bestemmelserne i direktivene 73/23/EEC og 89/336/EEC. [. . . ] The selected alarm schedule menu appears on the monitor as shown below. q ALA <<M O M M M M M M M ALA <<M M O ­ ­ ­ ­ ­ ­ R O F O O O O O O O R O O F ­ ­ ­ ­ ­ ­ M D F D D D D D D D w SCHEDU STA 0: 1 9: 2 9: 3 10: 1 11: 2 13: 3 17: 2 19: e L R 0 0 3 0 3 0 0 0 r t ALARM MODE3(AL=01) MODE =GROUP S E Q N O. = 0 2 E E E E E E E E << M1 S << M5 G M2 S M6 G M3 T M7 G M4 T M8 G >> >> E ( S U N. ­ 1 ) T STOP>> 0 9:00 0 9:30 0 10:00 0 11:30 0 13:00 0 17:00 0 19:00 0 20:00 2. parameter by moving the Joystick Controller, then enter a Group Sequence Number to be run on the selected monitor by pressing the Numeric button or the +1CAM INC or ­1CAM DEC button. Press the MON (ESC) button to return to the previous ALARM MODE 3 menu. M S C H E D U L E ( S U N. ­ 2 ) DE START STOP>> DE1 20:00 22:00 F 22:00 24:00 ­ ­­:­­ ­­:­­ ­ ­­:­­ ­­:­­ ­ ­­:­­ ­­:­­ ­ ­­:­­ ­­:­­ ­ ­­:­­ ­­:­­ ­ ­­:­­ ­­:­­ 4-4. ALARM SCHEDULE This table is used to enable and disable Alarm Modes according to the time of day and day of the week. There are sixteen (16) modes available in one day. Caution: To be able to set up this table, the ALARM MODE parameter on the ALARM MODE SELECT menu must be set to OFF. Select MODE SCHEDULE from the ALARM EVENT menu, then press the CAM (SET) button. The ALARM SCHEDULE menu appears on the monitor. 3. Move the cursor to position 1 by moving the Joystick Controller. Then set the Alarm Mode to MODE1, MODE2, MODE3 or OFF by pressing the +1CAM INC or ­1CAM DEC button. Move the cursor to position 2, 3, 4 and 5 by moving the Joystick Controller. Enter the desired hours (military time) and minutes by pressing the Numeric buttons. When satisfied with the programming of schedules on this page, press the HISTORY FWD button to select the next page. Repeat the above procedures until all schedules are programmed. Press the HISTORY BACK button to go back to the previous page. When satisfied with all schedules, press the MON (ESC) button to return to the previous ALARM SCHEDULE menu. Note: The programmed schedules are automatically placed in chronological order. Repeat the above procedures to programme other days. ALARM P R O G. C L E A R = S E T To programme or edit an Alarm Schedule, do the following: 1. [. . . ] Caution: This function will prevent operators with a lower priority from gaining control of a monitor. However, higher priority operators may still gain control of that monitor. 18. Log-out This function is used when an operator is leaving the Switcher, or no longer requires access to the system. Select 00 by pressing the Numeric buttons, then press the FUNCTION button to log out. 1 2 3 17-1. [. . . ]