User manual PANASONIC WJ-SX550C

[. . . ] System 500 Matrix Switcher Operating Instructions Matrix Switcher Model No. Model No. WJ-SX550C System Controller WV-CU550C Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. For U. S. A SA 1965 The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. [. . . ] Press the CAM (SET) key to execute the selection. Move the cursor to position 9 by moving the Joystick Controller. If the spot mode was selected in step 5, enter the desired camera number (1-128) by pressing the Numeric keys. Move the cursor to position 10 by moving the Joystick Controller. If the spot mode was selected in step 5, enter the desired preset position number, if applicable, by pressing the Numeric keys. Move the cursor to position 11 by moving the Joystick Controller. If the spot mode was selected in step 5, enter the desired dwell time (1-30) by pressing the Numeric keys. Move the cursor to position 12 by moving the Joystick Controller. If the spot mode was selected in step 5, press the Function F4 button to open the Pop Up Window. Select AUX On or Off by moving the Joystick Controller, and then press the CAM (SET) key to execute the selection. Move the cursor to position 13 by moving the Joystick Controller. Press the Function F4 button to open the Pop Up Window. Select either Set or Reset by moving the Joystick Controller, and then press the CAM (SET) key to execute the selection. Note: An "E" (Error) will appear in the table if an attempt is made to assign an incompatible mode to a monitor. For example, if an attempt is made to assign a Tour sequence to a monitor that is designated as a Spot monitor. Press the MON (ESC) key to escape from the programming mode. The cursor returns to position 4. 79 [Explanation of Table] The setup examples in the table on the preceding page are explained below. q Example 1: Spot (S) An alarm will cause the picture of the alarmed camera to be displayed on the designated monitor. Contents of Example 1 setup: When Alarm 1 is activated, Monitor 1 displays the picture of Camera 1 at preset position 1. When a second alarm, Alarm 2, is activated, Monitor 1 switches to the picture of Camera 2, and after 5 seconds again switches to the picture of Camera 1 for 10 seconds. After that Monitor 1 displays the two camera pictures alternately. Notes: · If plural Spot Cameras are assigned to a monitor in the event of alarm, it is recommended to program a Tour Sequence in advance. · To keep the latest alarmed Spot picture on a monitor, do the following: 1. [. . . ] To clear the alarm, first select the alarmed monitor, acknowledge the alarm with the ACK RESET button. Then, clear the alarm by again pressing the ACK RESET button or wait until the Auto Reset function clears the alarm after a predetermined amount of time has passed. 129 Symptom: The Alarm does not work. Check that the Alarm Mode is set to "Mode 1 - 3" or Timer on the Alarm Mode Select Menu of the Setup Menu. Check that the Alarm Input (Site or Board) is set to "On" on the Alarm Mode Select Menu of the Setup Menu. Symptom: The sequence does not stop after the programmed time. [. . . ]