User manual PANASONIC WJ-SX850

[. . . ] Vi deklarerar härmed värt fulla ansvar för att den produkt till vilken denna deklaration hänvisar är i överensstämmelse med standarddokument, eller andra normativa dokument som framställs i EEC-direktiv nr. Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämä ilmoitus koskee, noudattaa seuraavia standardeja tai muita ohjeellisia asiakirjoja, jotka noudattavat direktiivien 73/23/EEC ja 89/336/EE. Vi erklærer oss alene ansvarlige for at produktet som denne erklæringen gjelder for, er i overensstemmelse med følgende normer eller andre normgivende dokumenter som følger bestemmelsene i direktivene 73/23/EEC og 89/336/EEC. For Australia THIS APPARATUS MUST BE EARTHED. To ensure safe operation the three-pin plug supplied must be inserted only into a standard three-pin power point which is effectively earthed through the normal household wiring. [. . . ] · 9-segment or 16-segment screen does not display in quad sequence. Repeat the above procedures to assign other steps. SEQ Channels 4 - 16 flash at 2-second intervals (dwell time 2S). 8+12S: All segments of the 9-segment screen, except the bottom right, display pictures in the selected sequence and dwell time. (Example) 1 4 7 2 5 8 3 6 9 Dwell Time SEQ Channels 9 - 16 flash at 2-second intervals (dwell time 2S). 1. Move the cursor to the SEC (Second) area by pressing the cursor (C, D, A, B) buttons. Select the desired dwell time in the SEC area by pressing the Increment (+) or Decrement (­) button. Dwell Time can be selected between 0S and 30S. Note: A step assigned a dwell time of 0S is skipped. Notes: · The display position of 9-segment screen pictures in Sequence mode is fixed for channels 1 to 8. · This function is available only for the WJ-FS416 Video Multiplexer. 16 2. AUTO SKIP This item lets you enable or disable the Auto Skip function to skip any steps where no video signal is present at the Spot output. Proceed as described in MULTI OUTPUT, 1-1. AUTO SKIP on page 15. s System Setup Menu WJ-FS416 SETUP ALARM SETUP MONITOR OUTPUT SETUP REC OUTPUT SETUP SEQUENCE SETUP SYSTEM SETUP 3. Notes: · This selection is effective only when the Recording Mode in the Record Output Setup Menu is set to EXT. · To reset the warning, reconnect the CAMERA SW IN connector. Move the cursor to the CAM SW LOSS parameter. Select ON or OFF by pressing the + or ­ button. ON: Enables the display (SW LOSS) on the monitor screen. OFF: Disables the display. ABCDEFGHIJKLM NOPQRSTUVWXYZ ÄÜÖÆÑÅ 0123456789 =?'"#&()*+, -. /:;. (space mark) 4. After selecting the first character, press the B button. Repeat steps 3 to 4 above to complete the title. Repeat steps 2 to 5 to edit the titles of other channels. Press the MENU/ESC button to finalize the character selection. The title is set, and the display returns to SYSTEM SETUP. [. . . ] Turn on the Power Switch (;) while pressing the and buttons (WJ-SX850) or , and buttons (WJ-FS416). All LEDs light up. MENU ESC 5 12 13 4 , MENU ESC 3. Resetting is completed when the buzzer stops beeping. Note: Do not turn off the Power Switch until the buzzer stops beeping. OPERATING CONTROL OF SYSTEM UNITS (Supplementary) Operating the WJ-SX850 from the WV-CU360 System Controller · When operating from the WJ-SX850, the menu can be accessed without entering a password even if PASSWORD is set to ON. [. . . ]