User manual PANASONIC WV-MG14

[. . . ] · Avoid installing this bracket in the locations where salt damage occurs or corrosive gas is produced. Otherwise, the mounting portions will deteriorate and accidents such as a fall of the camera may occur. Failure to observe this may cause a fall of an inappropriate camera resulting in injury or accidents. Mount WV-NS202 on this bracket exclusively. [. . . ] · Avoid installing in the following locations. · Locations where it may get wet from rain or water splash (not only outdoor) · Locations where a chemical agent is used such as a swimming pool · Locations subject to steam and oil smoke such as a kitchen · Locations near flammable gas or vapor · Locations where radiation or x-ray emissions are produced · Locations subject to strong magnetic field or radio waves · Locations where it may be damaged by briny air such as seashores · Locations where the temperature is not within ­10 °C - +50 °C {14 °F - 122 °F}. · Locations subject to vibrations (This product is not designed for on-vehicle use. ) · Locations where the temperature may rapidly change such as the peripheral areas of the air outlets of air conditioners or doors facing outside. (In case of installing the camera in such locations, the dome cover may become foggy or condensation may be caused on the cover. ) · The screws and bolts must be tightened with an appropriate tightening torque according to the material and strength of the installation area. After tightening the screws or bolts, perform visual check to ensure tightening is enough and there is no backlash. · The pull-out strength of the installation area shall be 196 N {20 kgf} or more per 1 screw. · The protection sheet attached to the dome cover shall be peeled off after installation. 3 Major Operating Controls and Their Functions Mounting base Camera mounting plate Fixing screw to be used for cover fall prevention Hole for microphone cable Microphone stand* Decorative cover Dome cover * If a microphone is used, mount the microphone on the rubber-made microphone stand. Unless the microphone is used, cut the rubber with a nipper or conduct another treatment. <Installation sample> Roof space Safety wire angle (Accessory) Safety wire (Accessory) Ceiling mount bracket Ceiling board Decorative cover WV-NS202 Dome cover Inner shell 4 Installations Be sure to read "Precautions" on the page xx before installation. The Installation Guide of the network camera, WV-NS202, shall be read as well. q Loosen the fixing screw (unremovable) to be used for cover fall prevention. w Unhook the decorative cover from the hooks (3 positions) of the camera mounting plate and remove the decorative cover by turning it counterclockwise. e Take the inner shell out. Fixing screw to be used for cover fall prevention Hook LO CK 2. (Recommended tigtening torque: 0. 78 N·m {8. 0 kgf·cm} e Secure the mounting base with double nuts. Important: When securing this bracket on the ceiling, make sure that the four ceiling board fixing brackets are open as shown in the figure. Important: The cables shall be run from the opposite side of the mark, FRONT. Failure to observe this makes the cables unconnectable. 1st anchor bolt Nut Insert the anchor bolt Double nuts Ceiling board fixing screw Ceiling board fixing bracket Ceiling board Turn clockwise FRONT Cable inlet 8 10. Slide the covers located on the both lateral sides of the camera and put the inner shell on the camera until the hooks inside the inner shell are held in the holes of the camera (until a click is heard). Important: Put the inner shell down on the camera until the outside cover of the camera cannot be seen from the opening (from which the camera lens is visible) of the inner shell. If this integration is not successfully performed, the inner shell may be removed or the hidden part at the top of the screen may become larger in the WIDE mode. Inner shell Cover Hook Put on until a click is heard How to remove the inner shell Press the inner shell from the front and rear sides inward (at the same vertical position as the hooks) to bend the shell and remove the shell from the camera. Press from the front and rear sides inward to bend 9 11. Mount the camera on the camera mounting plate. q Put the camera onto the camera mounting plate with aligning the lock plate of the camera with the guide of the camera mounting plate and aligning the center of the camera mounting plate with the center of the screw for tripod mounting, and turn the camera clockwise. w Secure the camera with 1 piece of the camera fixing screw (supplied with the camera). (Recommended tightening torque: 0. 68 N·m {7. 0 kgf·cm}) Important: Be sure to mount the camera with holding the stationary portion of the camera. [. . . ] e Turn the camera mounting plate until g of the camera mounting base aligns with "ENDh" of the mounting base. r Tighten the 3 screws that were removed in Step 2. (Recommended tightening torque: 1. 6 N·m {16 kgf·cm}) Align A with A LO CK FRONT Align B with B Hooks for the decorative cover *1 position on the rear side LO CK Projections 11 Specifications Ambient temperature: Dimensions: Weight: Finish: ­10 °C- + 50 °C {14 °F - 122 °F} 185 mm {7-5/16"} in diameter x 145 mm {6-7/16"} in height Approx. 800 g {1. 77 lbs. } Main body: Treatment steel Decorative cover: ABS resin with silver metallic coating Dome cover: Acrylic resin Standard Accessories Operating Instructions (this book) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]