User manual PANASONIC WV-140

[. . . ] Be sure to install this bracket-specific safety wire. · Avoid installing this bracket in the locations where salt damage occurs or corrosive gas is produced. Otherwise, the mounting portions will deteriorate and accidents such as a fall of the camera may occur. [. . . ] Failure to observe this may cause a fall of the camera resulting in injury or accidents. · Periodic inspections shall be conducted. Rust on the metal parts or screws may cause a fall of the camera resulting in injury or accidents. Be sure to consult the dealer for the inspections. · Do not rub the edges of metal parts with your hand. Failure to observe this may cause injury. · Make sure that the installation area is strong enough to hold the total weight of the camera assembly (approx. · The screws that secure this bracket on a wall are not supplied. Prepare the screws according to the material, structure, strength and other factors of the mounting area and the total weight of objects to be mounted. Important: Put the inner shell down on the camera until the outside cover of the camera cannot be seen from the opening (from which the camera lens is visible) of the inner shell. If this integration is not successfully performed, the inner shell may be removed or the hidden part at the top of the screen may become larger in the WIDE mode. Inner shells Note: When the camera lens is pointed in the horizontal direction, the inner shell interferes with the camera's view, and consequently about upper half of the monitor screen is hidden in the WIDE mode. Hook Cover Put on until a click is heard Specifications Ambient temperature: Dimensions: Weight: Finish: ­10 °C - +50 °C {14 °F - 122 °F} 165 (W) x 206. 5 (H) x 217. 5 (D) mm {6-1/2" (W) x 8-1/3" (H) x 8-9/16" (D)} Approx. 950 g {2. 10 lbs. } Main body: Treatment steel Top and bottom covers: ABS resin with silver metallic coating Dome cover: Acrylic resin How to remove the inner shell Press the inner shell from the front and rear sides inward (at the same vertical position as the hooks) to bend the shell and remove the shell from the camera. Press from the front and rear sides inward to bend Standard Accessories Operating Instructions (this book) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Template . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 sheet Inner shell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mount the top cover on the wall and run the cables. Secure the top cover in either of the following two ways: q and w. Procure screws according to the installation area. q M4 screws, 4 positions (a) or w M4 screws, 2 positions ((a) upper 2 positions, not available in lower positions) and M6 or M8 anchor bolts, 2 positions (b) (a) (a) (b) (a) (a) (b) Important: The length of the anchor bolt projecting portion (the distance between the tip of the anchor bolt and the chassis attaching surface) shall be 7 mm {1/4"} or less. [. . . ] q M4 screws, 4 positions (a) or w M4 screws, 2 positions ((a) upper 2 positions, not available in lower positions) and M6 or M8 anchor bolts, 2 positions (b) (a) (a) (b) (a) (a) (b) Important: The length of the anchor bolt projecting portion (the distance between the tip of the anchor bolt and the chassis attaching surface) shall be 7 mm {1/4"} or less. Failure to observe this causes interference between the anchor bolt and bottom cover. Therefore, the bottom cover cannot be mounted. 7 mm {1/4"} Anchor bolt 5. [. . . ]