User manual PANASONIC WV-7230D

[. . . ] The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accom-panying the appliance. IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY. THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMP SOCKET. If a new plug is to be fitted please observe the wiring code as shown below. If in any doubt please consult a qualified electrician. [. . . ] Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämä ilmoitus koskee, noudattaa seuraavia standardeja tai muita ohjeellisia asiakirjoja, jotka noudattavat direktiivin 89/336/EEC. Vi erklærer oss alene ansvarlige for at produktet som denne erklæringen gjelder for, er i overensstemmelse med følgende normer eller andre normgivende dokumenter som fælger bestemmelsene i direktiv 89/336/EEC. CONTENTS PREFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . STANDARD ACCESSORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MAJOR OPTIONAL UNITS AND ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2 2 3 6 6 6 The model numbers listed in this Operating Instructions have no suffixed attached to it. -1- PREFACE The WV-7230DA System Controller, when combined with the optional WJ-SX550A Matrix Switcher and WJ-AD550 Extension Unit, allows for flexible control of 128 cameras and 16 monitors. When used in a system with either Receivers (WV-RC100, WV-RC150 or WV-RC170) or with Combination cameras (WV-BS200, WV-CS300, WV-CS500 or WV-CS600), the WV-7230DA can control camera functions such as zoom and focus and can also control accessory equipment such as Pan/Tilt Heads. In addition, the WV-7230DA can control sequential switching in systems programmed by the Set Up Menu of the WJ-SX550A Matrix Switcher. PRECAUTIONS · All necessary procedures, with regards to the installation of this unit should be made by qualified service personnel or system installers. Standard communications mediums such as modem, fiber and microwave can also be used. · Ergonomic design reduces the number of switches to only those with common functions. Secondary functions are accessed through function keys. · Flexible design allows for either table-top or rackmounting. -2- MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS q w e r t ALARM BUSY y F1 F2 F3 F4 UP ACK RESET BACK FORWARD SEQ SEQ ALT 1 4 2 5 8 3 6 PRESET IRIS CLOSE OPEN LEFT RIGHT @1 @0 !9 !8 AUX DEC INC -1CAM +1CAM STOP AF 1 2 7 MON ESC 9 CAM SET ZOOM TELE FOCUS NEAR DOWN 0 WIDE FAR System Controller WV-CU 550A u !7 !6 !5 !4 !3 !2 !1 !0 o i DATA IN OUT TERM ON OFF CONTROLLER UNIT NO. MODE 1-8 901 78 23 CONTROLLER ON OFF @2 @3 @4 456 @5 @6 @7 -3- 1. Alarm Indicator (ALARM) This LED indicator blinks to indicate an alarm tion exists. condi- 2. Busy Indicator (BUSY) This LED indicator lights up when one or more System Controllers with a higher operator priority than this one are used to perform a function with the same camera or monitor at the same time. While this indicator is lighted, operations from this System Controller are deactivated and can not be performed until the indicator goes off. 10. Preset Switch (PRESET) Auto Focus Switch (AF) PRESET: This switch, in combination with the Numeric Keys, is used to activate the preset function of the WV-CS500 or WV-CS600 Combination Camera. AF: This switch is used to activate the auto focus function when selected the specified camera such as the WV-CS600 Combination Camera. 3. Function Keys (F1/F2/F3/F4) These keys are used to select functions displayed on the Liquid Crystal Display. 11. [. . . ] When these switches are pressed at the same time for 3 seconds, the lens iris is set to the factory preset condition. 14. Stop Switch (STOP) This switch is used to stop a sequence that is being run on a monitor. 8. Focus Control (FOCUS NEAR/FAR) This control is used to adjust lens focus of specified lenses mounted on the camera. 15. Increment Switch (INC +1 CAM) This switch is used to move a sequence one step forward from the step that was previously stopped on the monitor by the Stop (STOP) Switch. [. . . ]