User manual PANASONIC WV-7330

[. . . ] Vi deklarerar härmed värt fulla ansvar för att den produkt till vilken denna deklaration hänvisar är i överensstämmelse med standarddokument, eller andra normativa dokument som framställs i EECdirektiv nr. Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämä ilmoitus koskee, noudattaa seuraavia standardeja tai muita ohjeellisia asiakirjoja, jotka noudattavat direktiivien 73/23/EEC ja 89/336/EE. Vi erklærer oss alene ansvarlige for at produktet som denne erklæringen gjelder for, er i overensstemmelse med følgende normer eller andre normgivende dokumenter som følger bestemmelsene i direktivene 73/23/EEC og 89/336/EEC. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK), NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is interned to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] Select [CLEAn] by moving the joystick up or down. Press the CAM/SET button [no-01] appears. 12 3. Enter a camera number (01 to 199) for cleaning first using Numeric buttons. The LED display shows a two-digit animations for cleaning on the left and a two-digit or a three-digit camera numbers (01-199) on the right. The last camera number appears when camera cleaning is over. To return to the previous display, press the MON/ ESC button. Notes: · To cancel the camera cleaning, press the MON/ ESC button. · Camera surveillance is disabled while camera cleaning continues. · All cameras are automatically cleaned in order. · Camera cleaning setting is valid only in cases where a combination camera is connected to the system. q Unit Connection Test Setting (12) Check that the power of the cameras and the other units are switched on. Select [UtESt] by moving the joystick up or down. 1 2 3 4 5 6 6 TX (B) TX (A) WV-7330 1 1 2 3 4 System Unit End 1 RX (B) RX (A) 6 5 6 15 OPERATING PROCEDURES The operating instructions for using the System Controller in a system are described below. For further information, refer to the Operating Instructions for the camera and for the individual system units. BASIC OPERATING FLOW LOG IN d SYSTEM OPERATION · Alarm Reset · Alarm Suspend · Alarm Suspend Cancel SYSTEM UNIT SELECTION d MONITOR SELECTION d CAMERA SELECTION d SYSTEM UNIT OPERATION · System Unit Setup · System Function · Alarm Recall MONITOR OPERATION · Switching of VTR and camera · Multiscreen Selection · Still · Electronic Zoom · Sequence · Sequence Pause CAMERA OPERATION · Camera Setup · Pan/Tilt (Slow) · Iris/Focus/Zoom · Preset Position · Home Position · Switching of Colour/Black & White · Auto Panning · Camera Patrol · Camera Patrol Stop · Camera Patrol Learn · Camera Function · Wiper/Defroster · Auxiliary Control 1/2 d LOG OUT 16 LOGIN/LOGOUT User authorization with password input is necessary for access to the system controller. If [User Certification OFF] is selected in the user authorization (certification) setting, password input is not necessary because the system controller is automatically ready for operation when the power is turned on. SET SET ESC s LOG IN 1. Insert the DC plug into the DC 9V IN jack and connect the AC adapter to an AC outlet. Ready for user password entry User password entry Blinks 2. The controller number, software version, and [LogIn] appears in order on the LED display. Enter a 5-digit user password with the Numeric buttons. The password appears as each [­] digit. Initial factory setting is [12345] (See page 12). If the user password is successfully entered for user authorization, LOGIN indicator lights up. The unit that is assigned to the UNIT A/UNIT button as number 1 is selected automatically. If its entry has failed, [Error] appears on the display. [. . . ] Note: For further information, refer to the Operating Instructions for the selected camera. Keys Used for camera with Setup Menu 8 q Camera Patrol Learning for Camera Patrol Operation There are two ways of setting camera patrol learning. One is to set up using the Camera Setup menu and the other is to set up while operating the camera. Follow the procedures below to set up while operating a combination camera. [. . . ]