User manual PANASONIC WV-BLR730

[. . . ] The wire which is coloured brown must be connected to the terminal in the plug which is marked with the letter L or coloured red. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK), NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is interned to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. The serial number of this product may be found on the top of the unit. [. . . ] The parameters you changed and set are stored as new values. If this procedure is not performed, the values are not stored. Completing this procedure makes these values remain valid until new values are stored, even if the power of the camera is off. · Editing the SPECIAL menu To edit the SPECIAL menu (change settings), proceed as for editing the CAM SET UP menu above. Move the cursor to RET, then press and simultaneously for 2 seconds or longer. The SPECIAL menu appears on the monitor. Select the item to be changed and change the setting as described for the CAM SET UP menu. ** SPECIAL ** UP SIDE DOWN AP GAIN PEDESTAL OFF . . . . I. . . . + PUSH SW CAMERA RESET RET END -20- SETTING PROCEDURES q RS485 Setup You can remote control this camera by using a specified extension unit such as computer with a modem. The RS485 menu is used to set the parameters of the items for RS485 site communication below. Move the cursor to RS485 of the SET UP menu and press . The RS485 menu appears on the monitor screen. ** RS485 SET UP ** UNIT NUMBER 1 BAUD RATE 19200 DATA BIT 8 PARITY CHECK NONE STOP BIT 1 XON/XOFF NOT USE WAIT TIME OFF ALARM DATA POLLING DELAY TIME OFF RET BAUD RATE This item is used to select the transmission speed for the RS485 communication. (BAUD is the unit of bit per second. ) 1. Move the cursor to the DELAY TIME parameter. Note: This item appears only when a two-line connection is used. · Installation of Software for RS485 Communication 1. Insert the Install Disk 1 to the C drive of your PC. When the window that says "Please insert the disk labeled: "Disk 2" into drive C:" appears on the monitor screen, insert the Install Disk 2 and press . When the installation is completed, the window that says "485_GUI Setup was completed successfully. " appears on the monitor screen. After installation of 485_GUI Setup is completed, open 485_GUI Setup, and set the RS485 communication parameters. q CAMERA Setup Move the cursor to CAMERA of the SET UP menu and press . The CAM SET UP menu appears on the monitor screen. Character Cursor 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ (). , '":;&#!?= +-*/%$ÄÜÖÆÑÅ SPACE POSI RET END RESET Pointer . . . . . . . . . . . . . . . . Character Area Command Editing Area 1. Camera Identification (CAMERA ID) Setting You can use the camera identification (CAMERA ID) to assign a name to the camera. The camera ID consists of up to 16 alphanumeric characters. You can select whether to have the camera ID displayed on the monitor screen or not. ** CAM SET UP ** CAMERA ID OFF ALC/ELC ALC SHUTTER --AGC ON SENS UP OFF SYNC INT MOTION DET OFF LENS DRIVE DC RET CAMERA ID menu 3. Move the cursor to the character you want to change by pressing / / / . [. . . ] · It takes about 0. 2 seconds for the alarm signal to reach the alarm terminal of the VTR after the camera detects the object. Because the alarm signal is multiplexed on the video signal, it may be mistakenly interpreted by other video equipment as a time code signal. Therefore, when camera is not used in a Panasonic Intelligent CCTV System select OFF to prevent the above from occurring. 8. Lens Drive Signal Selection (LENS DRIVE) This item is used to select the type of auto iris lens drive signal to be supplied to the lens from the auto iris lens connector. ** CAM SET UP ** CAMERA ID OFF ALC/ELC ALC SHUTTER --AGC ON SENS UP OFF SYNC INT MOTION DET OFF LENS DRIVE DC RET 1. [. . . ]