User manual PANASONIC WV-BM1400

[. . . ] 4 Monitor images from a single camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Monitor images from multiple cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Action at an Alarm Occurrence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Transmit Images onto an FTP Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] AUTO: Adjusts the white balance automatically. HOLD: Fixes to the white balance applied when the [SET] button is clicked. Default: AUTO [Aperture level] 9 steps (­4 - 4) are available for aperture level (sharpness). "­4" is the softest and "4" is the sharpest. Default: 0 [Flicker-less mode] Select "ON" or "OFF" to determine whether or not to use the flicker-less mode. When using the camera under fluorescent lamps and flickers appear, select "ON". Default: OFF 25 Configure the settings relating to audio [Audio] Click the [Audio] tab on the "Camera setup" page. ( page 16) The settings relating to audio can be configured on this page. Note: When a shorter interval is selected, delay time will be shorter. When a longer interval is selected, audio interruption may be diminished even though delay time will be longer. Select the interval according to the network environment. [Authentication] Select an access level for audio transmission from the following. Default: OFF [VMD alarm] Select "ON" or "OFF" to determine whether or not to perform the alarm action using the VMD function. Refer to page 31 for descriptions of how to set the VMD areas. Default: OFF [Command alarm] Select "ON" or "OFF" to determine whether or not to receive the command alarm. The command alarm is the function that notifies of Panasonic protocol alarm from the other cameras. When "ON" is selected, alarm actions will be performed between multiple cameras. Default: OFF 28 Configure the settings relating to the alarm image [Alarm image setup] Click the [Alarm] tab on the "Alarm setup" page. ( page 16) The settings relating to the alarm image to be transmitted to the FTP server can be configured on this page. The alarm image will be transmitted to the FTP server. To transmit alarm images to the FTP server, it is necessary to configure the settings in advance. ( page 38) Refer to pages 29 and 30 for further information about the settings relating to the alarm image and the alarm out connector. Important: Depending on the network line speed or the network traffic, images may not be transmitted at the exact designated interval or period. [Transmission interval] Select a transmission interval for the alarm image FTP transmission from the following. 0. 1 fps/0. 2 fps/0. 33 fps/0. 5 fps/1 fps Default: 1 fps [Number of images] Select the number of images to be transmitted from the following. [. . . ] When accessing the camera in the same subnet, it is recommended to enter the address of the camera in the "Don't Use Proxy For These Addresses" box. <When the camera and the PC are connected in the different subnet> Is the IP address of the default gateway set for the camera correct? 47 ­ 50 Symptom Cause/solution Reference pages Operating instructions (book) Cannot access from the browser. · Is the power of the camera on?Check if the power of the camera is turned on. · Is the viewer software installed on a PC?Check if the lens cap is detached. Operating instructions (book) ­ · Aren't there dusts or dirt on the lens? [. . . ]