User manual PANASONIC WV-BP102

[. . . ] 3 Monitor images on a PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Monitor images from a single camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Monitor images from multiple cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Record images on the SD memory card manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Camera control" when "On" is selected for "User authentication" ( Setup Instructions). *3 Operable by users who belong to the access level selected for "Permission level of audio trans. /recep. " on the [Audio] tab of the "Image/Audio" page ( Setup Instructions). Refer to Setup Instructions for further information about the access level. Note: When operated by a lower access level user, images displayed on the screen may be changed temporarily. This does not affect operation of the camera. Notes: · When a user is using the audio transmission function with "Interactive (half duplex)" selected, the receiver button and the transmission button will be inoperable for the other users. When "Interactive (full duplex)" is selected, the transmission button is inoperable for other users. · Possible duration of audio transmission is up to 5 minutes per transmission. When 5 minutes have passed, the audio transmission function will be canceled and the audio reception function will automatically be turned on. To turn the audio transmission function on, click the button again. · When the camera is restarted, the adjusted volume level (for both the audio transmission and reception) will return to the level that had been set on the [Audio] tab on the setup menu. ( Setup Instructions) · Actual volume level will change in three steps even though the volume cursor can be adjusted minutely. An alarm image (still picture) can be sent with the alarm mail as an attached file. The settings for alarm mail can be configured in the "Mail notification" section of the [Notification] tab of the "Alarm" page ( Setup Instructions) and the [Mail] tab of the "Server" page ( Setup Instructions). Notify of alarm occurrences to the designated IP addresses (Panasonic alarm protocol) This function is available only when a Panasonic device, such as the network disk recorder, is connected to the system. When "On" is selected for "Panasonic alarm protocol", the connected Panasonic device will be notified that the camera is in the alarm state. The settings for Panasonic alarm protocol can be configured in the "Panasonic alarm protocol notification" section of the [Notification] tab of the "Alarm" page. ( Setup Instructions) 10 Transmit images onto an FTP server Images can be transmitted to an FTP server. By configuring the following settings, transmission of images captured at an alarm occurrence or captured at a designated interval to an FTP server will become available. Important: · When using this function, set the user name and the password to access the FTP server to restrict users who can log into the FTP server. · To transmit images to the FTP server, select "Not use" for "SD memory card", or select "FTP error" for "Save trigger" on the [SD memory card] tab of the "Basic" page. Transmit an alarm image at an alarm occurrence (Alarm image transmission) An alarm image can be transmitted at an alarm occurrence to the FTP server. To transmit alarm images to an FTP server, it is necessary to configure the settings in advance. The settings for the FTP server can be configured on the [FTP] tab of the "Server" page. [. . . ] [PREV IMAGE] button The previous frame will be displayed and paused when this button is clicked during playback. Each time this button is clicked during pausing, the frame previous to the currently displayed frame will be displayed. Note: When the mouse button is held down while the mouse pointer is on this button, the image number will be decremented. When the mouse button is released, the decrement of the image number will stop and the image number displayed at the moment when the mouse button is released will be displayed. [. . . ]