User manual PANASONIC WV-BP104

[. . . ] The camera could be damaged by improper handling or storage. The installation should be made by qualified service personnel or system installers. Do not use strong or abrasive detergents when cleaning the camera body. Use a dry cloth to clean the camera when dirty. [. . . ] Move the cursor to an area where the backlight is bright and press SET to mask the area. The masked area appears alternately white and blinking when the cursor is on the area, or it turns white when the cursor is on other areas. To cancel masking, move the cursor to a masked area and press SET. When masking of the area is cancelled, it changes from white to normal. To cancel all the masking, press L and R simultaneously for 2 seconds. Adjust the video output level (LEVEL) by moving "I" cursor. Note: If ON is selected for SUPER-D3, a shadow (black line) may appear at the boundary between the bright and the dim portions. This is a natural phenomenon and does not indicate trouble. Blinking **ALC CONT** BACK LIGHT COMP SUPER-D3 MASK SET LEVEL OFF 6. VD2: Multiplexed vertical drive, highest priority LL: Line-Lock, follows the phase of supplied AC power, 2nd priority EXT (VBS): Composite color video or black-burst sync, 3rd priority EXT (VS): Composite monochrome video or composite HV sync, 4th priority INT: Internal sync, lowest priority Note: Selection is not available when VD2 is added to the camera. Selection from LL and VBS/VS is available when the respective sync is added. Line-Lock Vertical Phase Adjustment (V PHASE) · Select LL and press SET. The recorder will start recording the pictures. Select a mode for MOTION DET on the CAMERA SETUP menu. MODE1: Outputs alarm when a series of ** MODE1 ** motions is detected. LEVEL . . . . . . . . I MODE2: Outputs alarm when a series of + DWELL TIME 2S scene changes is detected. The MODE 1 menu opens when you DISPLAY MODE ALARM OFF select MODE1 and press SET . MASK SET 5. ON: Supplies the (color) burst signal with black-and-white composite video. Try both ON and OFF to match to connected devices (recorders, monitors, etc. ) that have different characteristics. 5. OFF: Enables the SET button to open the back-focus adjustment screen while the camera picture is displayed. ON: Disables the SET button from opening the back-focus adjustment screen. To reset the back focus to the default setting, press L and R simultaneously. SPECIFICATIONS Pick-up device: Scanning area: Scanning: Horizontal: Vertical: Synchronization: GEN LOCK input Video output: Resolution: 768 (H) x 494 (V) pixels, interline transfer CCD 4. 8 (H) x 3. 6 (V) mm (Equivalent to scanning area of 1/3" pick-up tube) 525 lines/60 fields/30 frames 15. 734 kHz 59. 94 Hz Multiplexed vertical drive (VD2), Line-locked, VBS/ VS, or Internal VBS/VS 1. 0 V[P-P] composite 75 /BNC connector 1. 0 V[P-P] NTSC composite 75 /BNC connector Horizontal 480 lines (C/L Normal), 540 lines typ. , 520 lines min. (C/L High), 570 lines (B/W) Vertical 350 lines (at center) 50 dB (Equivalent to AGC Off, weight On) 52 dB typ 0. 6 lx {0. 06 footcandle} at F1. 4 (C/L), 0. 5 lx {0. 05 footcandle} at F1. 2 (C/L), 0. 08 lx {0. 008 footcandle} at F1. 4 (B/W), 0. 06 lx {0. 006 footcandle} at F1. 2 (B/W) CS-mount (supplied with C-mount adapter) 12. [. . . ] LOW: Switches the mode at around 1 lux illumination. OFF SUPER-D3 ON: X2 AUTO X4 AUTO X6 AUTO X10 AUTO OPTIONAL ACCESSORIES Lenses : WV-LA2R8C3B, WV-LA4R5C3B, WV-LA9C3B, WV-LZ61/15, WV-LZA61/2S, WV-LZ62/8S, WV-LF4R5C3A, WV-LF9C3A, WV-LZF61/2 Notes: · Only AUTO is available when the ELC/ALC mode is set to ELC. · There may be cases where some types of system controllers cannot operate some of the SENS UP functions. If this happens, use the direction buttons on the camera. · When you select AUTO for SENS UP and ON for SUPER-D3, the SENS UP function has priority so that the SUPER-D3 function is not activated automatically. [. . . ]