User manual PANASONIC WV-BP120

[. . . ] CCTV Cameras WV-BP120/WV-BP124 WV-BP120 (Lens : option) WV-BP124 Before attempting to connect or operate this product, please read these instructions completely. ENGLISH VERSION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN For U. K. FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY. This appliance is supplied with a moulded three pin mains plug for your safety and convenience. Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 13 amp and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark or the BSI mark on the body of the fuse. [. . . ] Turn power off and refer servicing to qualified service personnel. Moisture can damage the camera and also create the danger of electric shock. · Never face the camera toward the sun. Whether the camera is in use or not, never face it toward the sun. Do use caution when operating the camera in the vicinity of spot lights or other bright lights and light reflecting objects. · Do not operate the camera beyond its temperature, humidity or power source ratings. Do not use the camera in an extreme environment where high temperature or high humidity exist. Use the camera under conditions where temperatures are within -10°C - +50°C (14°F - 122°F), and humidity is below 90%. The input power source is 220V - 240V AC 50 Hz for WV-BP120 or 24V AC 50 Hz for WV-BP124. -4- MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS WV-BP120 ALC ELC DC VIDEO (5) (6) (4) (3) (2) (8) (1) AC 24V IN GND 1 2 VIDEO OUT VIDEO OUT (7) (7) WV-BP120 -5- WV-BP124 (1) Lens (Option) See pages 10, 11, 12 and 13 for details on lens selection. (2) Flange-back Adjusting Ring This ring is used to adjust the back focal length or picture focus by rotating this ring to clockwise. for C-mount lens or counterclockwise for special Cmount (CS-mount) lens. Always set this ring to fully clockwise before mounting the lens. Do not turn this ring too much to counterclockwise when the C-mount lens is mounted as this could damage the inner glass and CCD image sensor. (3) Camera Mounting Screw Hole This threaded hole (1/4" - 20) is used to mount the camera onto a mounting bracket or tripod. (4) Auto Iris Lens Connector This 4-pin female connector supplies the power and either video signal or DC control signal to the auto iris lens. A 4-pin male connector, which can be mated with the camera's female connector, is supplied as a standard accessory (Part No. This male connector can be installed on lenses which have incompatible type connector. (5) Lens Selection Switch (ALC (DC/VIDEO), ELC) This switch is used to select the supplied auto iris control signal to the lens from the Auto iris lens Connector. DC: Choose this position when the auto iris control lens requiring DC control signal such as WVLA2. 8, WV-LA4R5C3A, WV-LA6B2, WVLA9C3A, WV-LZ61/10, WV-LA12B2, WV-LA18, WV-LA36, WV-LA4510, WV-LA608, WVLA1208, WV-LZ81/6, WV-LZ81/10, WVLZ83/6, is mounted on the camera. VIDEO: Choose this position when the auto iris control lens requiring video signal such as WV-LA8B, WV-LA16B, WV-LA25B, WV-LA50B, is mounted on the camera. -6- ELC: Choose this position used with a fixed or manual iris lens. (6) AC Power cord (7) Video Output Connector (VIDEO OUT) A 1. 0 V[p-p] 75 composite video signal is provided at this connector. (8) AC 24V In Terminal (AC 24V IN) This terminal accepts 24V AC power source (19. 5V - 28V). Be sure to connect grounding lead to the GND terminal. [. . . ] (2) Connect the lens cable to the Auto Iris Lens Connector on the camera when an auto iris lens is used. (3) Set the Lens Selection Switch to the proper position as follows. -15- DC: The mounted lens is one of the lenses listed on pages 10, 11 and 12 or one that requires the DC control signal for auto iris control. VIDEO: The mounted lens requires video signal for auto iris control. Note: Refer to item on page 6 for the lens selection switch. FOCUS OR FLANGE-BACK ADJUSTMENT The following adjustment should be made by qualified service personnel or system installers. [. . . ]