User manual PANASONIC WV-BP330

[. . . ] This appliance is supplied with a moulded three pin mains plug for your safety and convenience. Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 5 amp and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark or the BSI mark on the body of the fuse. If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced. [. . . ] Use a dry cloth to clean the camera when dirty. In case the dirt is hard to remove, use a mild detergent and wipe gently. Do not clean the CCD with strong or abrasive detergents. Use lens tissue or a cotton tipped applicator and ethanol. Do not aim the camera at bright objects. Whether the camera is in use or not, never aim it at the sun or other extremely bright objects. Otherwise, blooming or smear may be caused. Do not operate the camera beyond the specified temperature, humidity or power source ratings. Use the camera under conditions where temperature is between ­10°C - +50°C (14°F - 122°F), and humidity is below 90%. The input power source is 220-240V AC 50Hz for WV-BP330, 12V DC for WVBP332, and 24V AC 50Hz for WV-BP334. -4- MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS <WV-BP330> LL OFF ELC OFF DC Hi-Z INT AGC ON ALC BLC ON VIDEO G/L 75 V. PHASE WV-BP330 GEN-LOCK VIDEO OUT VIDEO LEVEL L H <WV-BP332> DC 12V IN OFF ELC OFF DC Hi-Z AGC ON ALC BLC ON VIDEO G/L 75 GEN-LOCK VIDEO OUT VIDEO LEVEL L H <WV-BP334> AC 24V IN GND LL OFF ELC OFF DC Hi-Z INT AGC ON ALC BLC ON VIDEO G/L 75 V. PHASE 1 2 GEN-LOCK VIDEO OUT VIDEO LEVEL L H -5- q Auto Iris lens Connector This connector is for connecting auto iris lens by a 4-pin male connector supplied as a standard accessory (Part No. w Back-focal Adjusting Ring This ring is adjusts the back-focal length or picture focus. Rotate this ring clockwise for a C-mount lens or counterclockwise for a CS-mount lens. e Lens (option) r Camera Mounting Screw Hole This hole is for mounting the camera onto a mounting bracket. t Power Cord (only WV-BP330) Connect this power cord to an electrical outlet of 220-240V AC 50Hz. y DC 12 V Input Terminal (DC 12V IN (only WV-BP332)) This terminal is for connecting the 12V DC power supply cord. u AC 24V Input Terminal (AC 24V IN (only WV-BP334)) This terminal is for connecting the 24V AC 50Hz power supply cord. i Synchronization Mode Selector (INT, LL (only WV-BP330 and WV-BP334)) Selects the camera synchronization mode from internal sync mode (INT) or line-lock mode (LL). INT: When no signal is supplied to the GEN-LOCK connector, the camera synchronization mode is set to internal 2:1 interlace. Whenever the gen-lock video signal is supplied to the GENLOCK connector, the camera synchronization mode is automatically set to external synchronization. LL: The camera synchronization mode is set to line-lock even if the gen-lock video signal is supplied to the GEN-LOCK connector. Note: Set this selector to INT for gen-lock operation. [. . . ] If the ring is rotated by force, the inner lens or CCD image sensor may be damaged. -14- INSTALLATION OF CAMERA · Mounting from the bottom This camera is designed to be mounted from the bottom, as shown below. The mounting hole is a standard photographic pan-head screw size (1/4" - 20). · Mounting from the top Remove the mount adapter from the bottom of the camera by removing the two fixing screws. Attach the mount adapter to the top as shown in the diagram, then mount the camera on the mounting bracket. [. . . ]