User manual PANASONIC WV-BP5564

[. . . ] Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Caution: To assure continued compliance, (example use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. For Canada SA 1965 The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. This Class A digital apparatus complies with Canadian ICES-003. The serial number of this product may be found on the top of the unit. [. . . ] The setting menu appears on the monitor screen. Set the lens iris level as desired with the joystick. -29- ** MANUAL CONT ** IRIS ····|···· CLOSE OPEN RET See the pages below for the settings respectively. Shutter speed: page 44 AGC: page 45 Electronic sensitivity enhancement: page 45 White balance: page 46 Motion detector: page 47 Auto focus: page 48 Dwell Time (DWELL TIME) · Move the cursor to DWELL TIME and set a dwell time with the joystick. Dwell time changes as follows: S stands for second(s), and MIN stands for minute(s). PRESET NO. 1* POSITION SET PRESET ID ALC/MANUAL DWELL TIME SCENE FILE PRESET SPEED ON ALC 10S 1 ········| L H Preset Speed Setting (PRESET SPEED) Move the cursor to PRESET SPEED and select a speed with the joystick. PRESET NO. 1* POSITION SET PRESET ID ALC/MANUAL DWELL TIME SCENE FILE PRESET SPEED ON ALC 10S 1 ········| L H RET DEL RET DEL To Return to the Preset Number Set Menu Move the cursor to RET and press the CAM (SET) button. The PRESET NUMBER SET menu appears with the * mark on the right of the preset position number. PRESET NO. 1* POSITION SET PRESET ID ALC/MANUAL DWELL TIME SCENE FILE PRESET SPEED ON ALC 10S 1 ········| L H Scene File Setting (SCENE FILE) 1. To set a scene file number Move the cursor to SCENE FILE and select a scene file number (1 to 10, or OFF) with the joystick. No scene file is selected at OFF. PRESET NO. 1* POSITION SET PRESET ID ALC/MANUAL DWELL TIME SCENE FILE PRESET SPEED ON ALC 10S 1 ········| L H RET DEL RET DEL To Return to the Setup Menu Move the cursor to RET and press the CAM (SET) button. ** PRESET NUMBER SET ** 1* 2 5 6 9 10 13 14 17 18 21 22 25 26 29 30 ID:DOOR RET 3 7 11 15 19 23 27 31 4 8 12 16 20 24 28 32 2. In such cases, pan the camera fully several times. If this does not eliminate the problem, refer servicing to qualified service personnel. To set ENDLESS to ON/OFF Move the cursor to ENDLESS, and select ON or OFF with the joystick. ** AUTO PAN ** POSITION SPEED ENDLESS DWELL TIME PAN LIMIT ZOOM LIMIT RET START END ····|···· L H ON 1S OFF OFF (2) Move the joystick to select a panning starting point and press the CAM (SET) button. ON: The camera pans from the starting point to the endpoint, and keeps rotating in the same direction to return to the starting point. Set PAN LIMIT to OFF before ENDLESS is set to ON. -32- OFF: The camera pans from the starting point to the endpoint, and rotates backward to the starting point. This movement is repeated over and over. To set a dwell time Move the cursor to DWELL TIME and select a dwell time with the joystick. ** AUTO PAN ** POSITION SPEED ENDLESS DWELL TIME PAN LIMIT ZOOM LIMIT RET START END ····|···· L H OFF 1S OFF OFF (2) Move the cursor to ZOOM, press the CAM (SET) button, move the joystick to settle the ZOOM position and return to the AUTO PAN menu. The manual zoom operation is not available in the TELE direction beyond the settled zoom position. ** ZOOM LIMIT ** ZOOM PUSH SET U ZOOM D RET Dwell time changes as follows: (unit: s) 0S 30S 1S 20S 2S 10S 3S 5S 7. To set pan limit ON/OFF Move the cursor to PAN LIMIT and select ON or OFF with the joystick. ON: Manual pan is limited from the starting point to the endpoint specified by position setting. Set ENDLESS to OFF before PAN LIMIT is set to ON. [. . . ] SENS UP: AUTO ON SENS UP: AUTO OFF Increases electronic sensitivity enhancement (AUTO) one step. Decreases electronic sensitivity enhancement (AUTO) one step. Increases line lock phase (FINE) one step. Decreases line lock phase (FINE) one step. [. . . ]