User manual PANASONIC WV-BPR550

[. . . ] The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol I or coloured green or green-andyellow. The wire which is coloured blue must be connected to the terminal in the plug which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal in the plug which is marked with the letter L or coloured red. We declare under our sole responsibility that the product to which this declaration relates is in conformity with the standards or other normative documents following the provisions of Directives EEC/73/23 and EEC/89/336. Wij verklaren als enige aansprakelijke, dat het product waarop deze verklaring betrekking heeft, voldoet aan de volgende normen of andere normatieve documenten, overeenkomstig de bepalingen van Richtlijnen 73/23/EEC en 89/336/EEC. [. . . ] The camera could be damaged by improper handling or storage. Do not expose the camera to rain or moisture, or try to operate it in wet areas. Turn the power off immediately and ask a qualified service person for servicing. Moisture can damage the camera and also create the danger of electric shock. Do not use strong or abrasive detergents when cleaning the camera body. Use a dry cloth to clean the camera when dirty. In case the dirt is hard to remove, use a mild detergent and wipe gently. Afterwards, wipe off the remained part of the detergent in it with a dry cloth. Do not clean the CCD with strong or abrasive detergents. Use lens tissue or a cotton tipped applicator and ethanol. Do not aim the camera at bright objects. Caution: To use in ALC mode, make sure to set the selector (ELC) to OFF position. To use in ELC mode, make sure to set the selector (ALC) to OFF position. !1 Lens Drive Signal Selector (VIDEO, DC) Lets you select the mode according to the type of auto iris lens drive signal to be supplied to the lens from the auto iris lens connector. VIDEO: Select this mode if you are using the auto iris lens that requires a video drive signal. DC: Select this mode if you are using the auto iris lens that requires a DC drive signal. c cs !2 Video Output Connector (VIDEO OUT) This connector is for connecting with the VIDEO IN connector of the video monitor. Whenever the multiplexed vertical drive (VD2) signal is supplied to this connector, the camera synchronization mode is automatically set to Vertical Drive. Caution: Connect to 12 V DC (10. 5 V-16 V) or 24 V AC (19. 5 V-28 V) class 2 power supply only. Make sure to connect the grounding lead to the GND terminal when the power is supplied from a 24 V AC power source. CONNECTIONS A. WV-BPR550 (220 V - 240V AC 50Hz) Connect the power cord to an electrical outlet of 220 V - 240 V AC 50Hz. Installation of Auto Iris Lens Connector Install the lens connector (YFE4191J100) when using a video drive ALC lens. The installation should be made by qualified service personnel or system installers. Cut the iris control cable at the edge of the lens connector to remove the existing lens connector and then remove the outer cable cover of the supplied connector as shown in the diagram. The pin assignment of the lens connector is as follows: Pin 1: Power source; +9 V DC, 50 mA max. [. . . ] WV-BP144 (24 V AC 50 Hz) cs q 1 2 Caution for Mounting the Lens 24 V AC, 50 Hz (19. 5 V - 28 V) Recommended wire gauge sizes for 24 V AC line Copper wire size (AWG) Length of Cable (Approx. ) (m) (ft) #24 #22 #20 #18 (0. 22 mm2) (0. 33 mm2) (0. 52 mm2) (0. 83 mm2) 95 314 150 495 255 842 425 1 403 The lens mount should be a C-mount or CS-mount (1"-32UN) and the lens weight should be less than 450 g (0. 99 lbs). If the lens is heavier, both the lens and camera should be secured by using the supporter. The protrusion at the rear of the lens should be as shown below. Video Cable 1. It is recommended to use a monitor whose resolution is at least equal to that of the camera. [. . . ]