User manual PANASONIC WV-CF20

[. . . ] 5 MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 SYSTEM INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Additional features of the WV-CF20 include: · Up to 8 WV-CF20 System Controllers can be connected in a system by using standard RS-485 shielded 4-wire twisted pair cable. Can also be combined with standard communication media such as modems, fiber optics and microwave can also be used. · Ergonomic design reduces the number of switches to only those with common functions. Secondary functions are accessed through function keys. · Flexible design allows for either table-top or rack-mounting. 4 PRECAUTIONS · Refer all work related to the installation of this product to qualified service personnel or system installers. · Do not attempt to disassemble the appliance. To prevent electric shock, do not remove screws or covers. There are no user-serviceable parts inside. Contact qualified service personnel for maintenance. · Handle the appliance with care. Do not strike or shake it, as this may damage the appliance. i Focus Control (FOCUS NEAR/FAR) Adjust the lens focus of cameras equipped with the specified lens. o Zoom Control (ZOOM TELE/WIDE) This control is used for zooming cameras equipped with the specified lens. !0 Preset Button (PRESET) Auto Focus Button (AF) PRESET: This button, in combination with the Numeric keys, is used to move the selected camera to a preset position in a system equipped with the specified cameras. AF: Pressing this button will automatically set the lens focus of a specified camera such as the WV-CS854. !1 Camera (Set) Key [CAM (SET)] CAM: Used for camera selection. To select a camera, enter the desired camera number with the Numeric keys, and then press the CAM key. SET: This key, in combination with the Numeric keys, is used to enter numeric input, such as operator ID and password. It is also used to execute the currently highlighted selection and to enter a submenu in the Setup Menu of the Matrix Switcher. !2 Numeric Keys (0 - 9) These keys are used for numeric input into the system, such as the camera and monitor number, sequence number, preset position, etc. !3 Monitor (Escape) Key [MON (ESC)] MON: This key is used to select a monitor. To select a monitor, press the corresponding Numeric keys, followed by the MON key. ESC: This key is used to escape from the currently highlighted selection on the Setup Menu of the Matrix Switcher. [. . . ] !8 Alternate Button (ALT) This button activates the alternate function of dual-function control buttons. #4 Mode Selection Switch (MODE) These switches are used to set the mode of the System Controller connected to the Matrix Switcher. Set the switches as shown below. MODE Normal Mode ON 1 2 3 4 MODE CAM-P Mode !9 Forward Sequence Button (FORWARD SEQ) This button is used to run a selected Program or Tour Sequence in forward direction on the active monitor. Refer to the Operating Instructions of WJ-FS616 for further details. 9 SYSTEM INFORMATION Please note that the following functions were added to improve the operation of the combination cameras. s Version Information q WJ-SX550 Series Matrix Switcher The onscreen display indicates the version in "Cold Start" or "Normal Start" during the power up procedure. Matrix Model Switcher WJ-SX550B Start" SW. Position 01 NTSC 1 VS s Additions q Selection of Pan/Tilt Speed The Pan/Tilt speed can be changed by selecting a mode in the menu (A1) displayed on the LCD display of the controller. [. . . ]