User manual PANASONIC WV-CF254

[. . . ] Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. SA 1965 The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. The serial number of this product may be found on the top of the unit. [. . . ] This determines the endpoint and the cursor moves to POSITION. To set a panning speed Move the cursor to SPEED, and move the joystick to the right or left to set a panning speed. The panning speed increases when the joystick is moved to the right, and decreases when it is moved to the left. Caution: If the panning range is changed after the camera has not panned for a long time or has been panning in the same panning range, the picture may not be clear or noise may appear. In this case, pan the camera fully several times. If this does not eliminate the problem, refer servicing to qualified service personnel. POSITION SPEED PAN LIMIT ENDLESS DWELL TIME RET START END ····|···· L H OFF OFF 1S ** AUTO PAN ** POSITION SPEED PAN LIMIT ENDLESS DWELL TIME RET START END ····|···· L H OFF OFF 1S ** AUTO PAN ** POSITION SPEED PAN LIMIT ENDLESS DWELL TIME RET START END ····|···· L H OFF OFF 1S ** AUTO PAN ** POSITION SPEED PAN LIMIT ENDLESS DWELL TIME RET START END ····|···· L H OFF OFF 1S 23 5. To set pan limit ON/OFF Endpoint Move the cursor to PAN LIMIT and select ON or OFF by movCamera ing the joystick to the right or left. Start-end range of The factory default setting is OFF. ON: Manual pan is limited from the starting point to the end- auto pan point specified by position setting. Set ENDLESS to OFF before PAN LIMIT is set to ON. Starting point OFF: Manual pan is not limited. Make sure that LOCAL is selected in this case. Setup menu ** SET UP MENU ** PRESET 1 MAP HOME POSITION OFF OFF SELF RETURN OFF AUTO MODE AUTO PAN KEY AUTO PAN LOCAL/REMOTE LOCAL PATROL STOP CLEANING OFF CAMERA RS485 SET UP 25 s Patrol Learn and Patrol Play (PATROL) A routine of manual operations can be stored for 30 seconds at the maximum and reproduced repetitively. Set the following parameters for the patrol learn starting position. These parameters are stored when the patrol learn mode starts. · PAN/TILT/ZOOM/FOCUS · IRIS · SHUTTER · AGC · WHITE BALANCE · IMAGE HOLD · CAMERA ID · PAN LIMIT · CLEANING After starting the patrol learn, the following manual operations are stored. · PAN/TILT/ZOOM/FOCUS operation · IRIS operation · Preset positioning 2. Open the SET UP menu and move the cursor to PATROL. Select LEARN, PLAY or STOP for PATROL by moving the joystick to the right or left. LEARN: A series of manual operations is stored. STOP: LEARN or PLAY is not activated. Special 1 menu ** SET UP MENU ** PRESET 1 MAP HOME POSITION OFF OFF SELF RETURN OFF AUTO MODE AUTO PAN KEY AUTO PAN LOCAL/REMOTE LOCAL PATROL STOP CLEANING OFF CAMERA RS485 SET UP Patrol Learn with a Controller Having the PATROL Key 1. Press the PATROL LEARN key and the PROGRAM key simultaneously to start the patrol learn. The setup menu changes to show "LEARNING" and the starting points are stored. [. . . ] Do not shrink the cableentry seal until it has been ascertained that the unit is functioning. · CONNECT THIS TO 24 V AC CLASS 2 POWER SUPPLY ONLY. Insert the wire until A position wire until A position Insert and clamp the contacts. and clamp 48 · RS485 Connection Brown GND Red Data transmission Orange Yellow Data reception Green T (B) T (A) R (B) R (A) Note: Use the cable that is described below for RS485 site communication. · Shielded, twisted pair cable · Low impedance · Wire gauge size is thicker than AWG #22 (0. 33 mm2). 49 SYSTEM CONNECTIONS Color CCTV camera Max. [. . . ]