User manual PANASONIC WV-CK1420A

[. . . ] The camera could be damaged by improper handling or storage. Do not use strong or abrasive detergents. Use a dry cloth to clean the camera body when dirty. In case the dirt is hard to remove, use a mild detergent and wipe gently. [. . . ] Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS qw 2nd transport protection screw (Red) "F" stands for flash mounting. This model can be mounted on a two-gang junction box (4" x 4") preinstalled in the wall or ceiling. 46mm (1-13/16") 83. 5mm (3-5/16") SA 1966 The serial number of this product may be found on the top of the unit. You should note the serial number of this unit in the space provided and retain this instruction as a permanent record of your purchase to aid identification in the event of theft. Serial No. Space for heater unit u e r i Mounting the Camera Disassembly of the camera 1. Remove the dome cover by loosening three tamper-proof screws using the supplied bit. WARNING: To prevent fire or electric shock hazard, do not expose this appliance to rain or moisture. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. o !0 t y Camera fixing screw x 4 (procured locally) OFF SYNC BLC LL OFF* SOFT ON INT* ON SHARP* PREFACE The WV-CW244 series is a 1/3" CCD color camera designed for use in a video surveillance system. The camera features a high picture quality thanks to the use of digital signal processing LSIs, and easy installation. !1 1. Space Prepare a space larger than ø160 mm. Junction box Procure and install a junction box that meets the dimensions in the figure. Camera Fixing Screws Procure four screws (M4) suitable for the junction box. Cable route Cables will go behind the junction box. If the same power source is used, turning the heater on and off may disturb the camera images. · When servicing, pay attention to high temperature on the surface of the unit. Disconnect the harness and wait until it cools. · When you install the camera in a low-temperature location and start operating it, it may take time (around 30 minutes) for the inside of the camera to warm up. Cut power once then Supplied screw Supplied screw supply power again. Adhesive tape Adhesive tape Fold Fold Harness Harness Notes: · Do not hold the camera by lens unit to adjust panning, tilting, or azimuth. · The video output to the BNC will be interrupted while an LCD monitor is connected to the video jack. Panning table Tilting lock screw (stainless) Detail: White balance: Lens Mount: Lens Focal length: Maximum aperture ratio: Angular field of view: Focusing range: Ambient operating temperature: Mounting the camera 1. Fix the camera to the installation surface. WV-CK1420A · Fix the camera on the junction box using four screws (locally procured). WV-CW244S · Fix the supplied bracket on the wall/ceiling using four screws (locally procured). · Fix the camera on the bracket using four screws (supplied). Perform connections referring to Connections. [. . . ] Connect the heater power cable of the camera. (See Connection. ) STANDARD ACCESSORIES FAR TELE NEAR WIDE Operating Instructions (this document) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tamperproof screw bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Camera mounting bracket (supplied only to WV-CW244S) . . . . . . . . . . . . . . . [. . . ]