User manual PANASONIC WV-CL352

[. . . ] Note: The waterproof process should be made by qualified service personnel or system installers according to the local requirement. Fixing the supplied camera mounting arm directly · You can fix the camera mounting arm to a junction box installed on the wall. · You can fix the camera mounting arm directly to the wall with a cable access hole. For installation, refer to Fixing the Mounting Arm Directly. Note: Attach the mounting arm to hinges on the side opposite to the wall. Fix the camera to the camera mounting arm. Fixing screw for adapter box (Supplied) x1 (M4 x 35) Caution: Before attempting to connect or operate this product, please read the marking on the top. For U. S. A Note: Mounting screws are not supplied. [. . . ] Fix the camera mounting arm to the adapter box with four supplied screws. Fix the mounting arm covers to the mounting arm with two supplied screws. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. I SD I Installing the adapter box directly to the wall With the mounting screws (locally procured), fix the adapter box to a junction box or directly to the wall. 46 mm {1-13/16"} Cable access hole 24. 5 mm {31/32"} Mounting arm Adapter box SA 1965 The lightning flash with arrowhead symbol, within an equilateral triangle, is interned to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Mounting arm Note: Lead the camera cables out of the cable hole of mounting arm. Adapter box 5. Pass the cables through the cable clamp of mounting arm, and then to the wall. 22 mm {14/16"} Model No. Serial No. SA 1966 Center of adapter box Fixing screws for adapter box and mounting arm (Supplied) x 4 (M5 x 20) WARNING: All work related to the installation of this product should be made by qualified service personnel or system installers. CAUTION: An ALL-POLE MAINS SWITCH with a contact separation of at least 3 mm {0. 12"} in each pole shall be incorporated in the electrical installation of the building. Cable clamp Mounting screws (Locally procured) x 4 Adapter box Cable access hole (Used for wiring) (G3/4" internal thread) 83. 5 mm {3-5/16"} The serial number of this product may be found on the top of the unit. You should note the serial number of this unit in the space provided and retain this instruction as a permanent record of your purchase to aid identification in the event of theft. Hole 6 mm (W) x 10 mm (H) {1/4" (W) x 13/32" (H)} 4 37 W V-C W I SD I Fixing screws for covers (Supplied) x 2 (M3 x 6) Covers x 2 Note: Do not expose the cables to sunlight. Installing the adapter box to a junction box I Preface Panasonic WV-CL352 is designed for installation on the wall, using a camera mounting arm or the supplied adapter box. To facilitate wirings, it is recommended to align two junction boxes. I Fixing the Mounting Arm Directly Notes: · For outdoor use, the mounting screws and screw holes require waterproofing. Refer to Waterproof Process in this document. · Avoid waterproofing the drainage hole. I Adjusting the Camera Angle 1. Remove the rear cover by loosening the fixing screw. 46 mm {1-13/16"} Hole 6 mm (W) x 10 mm (H) {1/4" (W) x 13/32" (H)} 83. 5mm {3-5/16"} I Precautions · Refer all work related to the installation of this product to qualified service personnel or system installers. The maximum extensible length is shown in the table. Type of coaxial cable RG-59/U (3C-2V) 250 825 RG-6/U (5C-2V) 500 1 650 RG-11/U (7C-2V) 600 1 980 RG-15/U (10C-2V) 800 2 640 I Attaching the Supplied Mounting Adapter If you use a camera mounting arm locally procured, you need to use the supplied mounting adapter. Remove the camera neck from the camera head by loosening the camera neck screws. Attach the supplied mounting adapter to the camera head by tightening the four supplied screws. I SD I Panning lock screw (Hexagon socket screw) Recommended (m) maximum cable length (ft) W V-C W 37 4 G Cable Length and Wire Gauge I Adjusting the Focus 1. Remove the front cover by loosening the four fixing screws. Adjust the lens zooming by moving the zooming ring to T (Tele) or W (Wide). Adjust the lens focus by performing 1) to 3). The focus lever, locked with the focus lock screw, will be adjustable. 2) Move the focus lever to F (Far) or N (Near). 3) After adjustment, tighten the focus lock screw. Focus lock screw (Locking the focus lever) Front cover 24 V AC The recommended cable length and thickness are shown in the table for reference. The voltage supplied to the power terminals should be within 19. 5 V AC and 28 V AC. Recommended wire gauge for 24 V AC line. Copper wire size (AWG) Length of Cable (Approx. ) (m) (ft) #24 #22 #20 #18 (0. 22 mm2) (0. 33 mm2) (0. 52 mm2) (0. 83 mm2) 20 65 30 100 45 160 75 260 Cautions: · Be sure to use the supplied screws. [. . . ] Shrinking the cable-entry seal is a one-time procedure. Do not shrink the cable-entry seal until it has been ascertained that the unit is functioning. CONNECT THIS TO CLASS 2 POWER SUPPLY ONLY. All interconnecting devices must be UL Listed. I Standard Accessories Instructions (this document). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]