User manual PANASONIC WV-CL354

[. . . ] Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. SA 1965 The lightning flash with arrowhead symbol, within an equilateral triangle, is interned to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. The serial number of this product may be found on the top of the unit. [. . . ] Move the cursor to the ALC/ELC parameter. ALC Mode with SUPER-D2 ON Super Dynamic2 Function (SUPER-D2) The important object in a scene is usually placed in the center of the monitor's screen. In SUPER-D2 mode, more photometric weight is given to the center of the screen (where the important object is located) than to the edge of the picture (where a bright backlight would most likely be located). You can use the SUPER-D2 function if you select ALC. It eliminates interference by strong background lighting which makes the camera picture dark, such as a spotlight. After selecting ALC, press to open the ALC CONT menu. Move the cursor to the SUPER-D2 parameter and select ON ** ALC CONT ** BACK LIGHT COMP SUPER-D2 MASK SET LEVEL RET END . . . I. . . . . If you want to adjust the video output level, move the cursor to the "I" position. Adjust to the desired level by pressing or . ** ALC CONT ** BACK LIGHT COMP SUPER-D2 LEVEL RET 2-2. ALC Mode with SUPER-D2 OFF and ELC Mode Note: If ELC is selected, set MASK SET according to this procedure. Move the cursor to the SUPER-D2 parameter and select OFF. The preset values for SENS UP (electronic sensitivity enhancement) change by pressing or as shown right: OFF X32 FIX X2 AUTO X16 FIX X4 AUTO X10 FIX X6 AUTO X6 FIX X10 AUTO X4 FIX X2 FIX OFF Notes: · When ON is selected for SUPER-D2 in the ALC CONT menu, FIX is not available for this item. · When you select AUTO for SENS UP and ON for SUPER-D2, the SENS UP function has priority so that the SUPER-D2 function is not activated automatically. · While the SENS UP function is selected, noise, spots or a whitish phenomenon may appear in the picture when the sensitivity of the camera is increased. Synchronization Setting (SYNC) You can select internal sync mode (INT) or line-lock mode (LL). Additionally, this model accepts the VBS signal (color composite video or blackburst signal) and VS signal (B/W composite video or composite sync signal). The VD2 signal (multiplexed vertical drive signal) with the composite video output signal from external equipment such as a Matrix Switcher is also acceptable. Whenever the VD2 signal is supplied to this camera, the camera automatically switches to the VD2 sync mode. 1. Move the cursor to the SYNC parameter and select line-lock (LL) or internal (INT). If LL is selected, the SYNC menu appears. (If INT is selected, the synchronization mode is automatically set to internal sync pulse, and the menu is not displayed. ) Important Notice: 1. The priority for the sync modes is as follows: 1. [. . . ] · It takes about 0. 2 seconds for the alarm signal to reach the alarm terminal of the VCR after the camera detects the object. Because the alarm signal is multiplexed on the video signal, it may be mistakenly interpreted by other video equipment as a time code signal. Therefore, when the camera is not used in a Panasonic Intelligent CCTV System select OFF to prevent the above from occurring. 9. Lens Drive Signal Selection (LENS DRIVE) This item is used to select the type of auto iris lens drive signal to be supplied to the lens from the auto iris lens connector. [. . . ]