User manual PANASONIC WV-CL924

[. . . ] These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices). [. . . ] Metal material: Use M6 or M5 bolts and nuts for mounting. Concrete wall: Use M6 or M5 anchor bolts for mounting. (Recommended tightening torque M4 : 0. 8 N·m {8 kgf·cm} M5 : 1. 5 N·m {15 kgf·cm} M6 : 2. 5 N·m {25 kgf·cm}) · Be sure that the arrow on the installation bracket is pointing upwards. · A pull-out force in excess of 294 N {30 kgf} is required for each screw used in the installation. · Use sufficient reinforcement for installations on ceilings that are made of gypsum board and are weak. Fixing the bracket (accessory) · Use the bracket to install the camera on a wall or ceiling that is provided with a hole for passing the cable through or on exposed piping. · Screws for fixing the bracket to a wall or ceiling are not provided. Choose screws in accordance with the materials and structure of the installation location. · Screws for fixing the camera to the bracket are provided with the camera. 20 Installing the Camera 1 Install the mounting bracket. Fix the mounting bracket directly into the ceiling or wall or into the imbedded box using the four screws prepared in advance. (Note that screws for installation are not provided. ) When using the imbedded box, we recommend using two boxes in a row as shown in the figure below on the right. Wind butyl rubber tape around the connections. Wrap butyl rubber tape around the joint of the LAN cable connector. Power cable 1 2 3 LAN cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Note · How to wrap butyl rubber tape (provided). Stretch the tape to about twice its length (see Stretch about 2x figure on the right), and wrap it around the cable. Sufficient waterproofing performance cannot be obtained unless the tape is sufficiently stretched. 2x · Waterproof the cable when installing the camera outdoors. The camera body is waterproof (JIS IP66 or equivalent) only when installation specified in this document and appropriate waterproofing is conducted correctly. The mounting bracket is not waterproofed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Important · When wiring the cable by exposed wiring, be sure to use a sleeve to prevent the cable from being exposed to the direct sunlight. · Install the camera so that the cable is at the bottom side of the camera. Draw out the cable to the side of the mounting fixture, set it facing down, and then wire it facing up. Bottom side · When installing the camera on a wall, install it so that the water drain groove is facing down. Also, do not block the water drain groove. Blocking the water drain groove will prevent the dehumidifying element at the rear of the camera from functioning. [. . . ] : Alarm action will be performed when a change (i. e. motion) is detected in the image in the set VMD area. * VMD stands for "Video Motion Detector". : Alarm action will be performed when this camera has been interfered with, for example, when it has been covered with a cloth or when its direction has been changed. [. . . ]