User manual PANASONIC WV-CL934

[. . . ] Color CCTV Cameras Operating Instructions Model Nos. WV-CL930 WV-CL934 2X T W VL 6~1 V-L ENS 2m Z80 m 1 /2 :1. 4 (Lens: option) Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. No model number suffix is shown in this manual. ENGLISH VERSION WARNING: · This apparatus must be earthed. · Apparatus shall be connected to a mains socket outlet with a protective earthing connection. · The mains plug or an appliance coupler shall remain readily operable. [. . . ] Step 4 To change the video output level (image contrast), move the cursor to "LEVEL" and adjust the level with use of the right or left button. RET TOP END "ALC+CONT" screen **ALC+CONT** BACK LIGHT COMP PRESET PEAK MODE MASK SET LEVEL OFF OFF . . . |. . . 128 + RET TOP END "ELC CONT" screen **ELC CONT** BACK LIGHT COMP PRESET PEAK MODE MASK SET LEVEL OFF OFF . . . |. . . 128 + RET TOP END Mask setting screen 27 Flare compensation mode If a lens flare is undesirable, move the cursor to "PEAK MODE" and use right or left button to select "ON". OFF (default): Does not perform flare compensation. 3. Electronic shutter setting [SHUTTER] The variation in electronic shutter speed allows users to perform the following. · Increased shutter speed prevents blurring fast-moving subjects. The electronic shutter speed is selectable from the following: OFF (1/60) (default), 1/120, 1/250, 1/500, 1/1 000, 1/2 000, 1/4 000, and 1/10 000 Notes: · When "ALC/ELC" is set to "ELC" or "ALC+" ( page 25), the shutter setting cannot be performed. "OFF (1/60)" is automatically selected. · If the controller, WV-CU254 or WV-CU204 is used, SW LED and the status of "SHUTTER" are not correctly displayed. 28 4. Gain control setting [AGC] "CAMERA SETUP" screen **CAMERA CAMERA ID ALC/ELC SHUTTER AGC SENS UP SYNC WHITE BAL MOTION DET DNR RESOLUTION BW MODE SETUP** 1/2 OFF ALC OFF ON OFF INT ATW1 OFF HIGH HIGH Step 1 Move the cursor to "AGC" and use right or left button to select "ON" or "OFF". ON (default): Automatically increases the gain to make the screen brighter when the illuminance of the subject becomes darker. (The normal image remains. ) Step 2 Move the cursor to "ON" and press the setting button to call up the "AGC MAX" screen. "AGC MAX" screen ** AGC MAX ** LEVEL . . . |. . . 128 + RET TOP END Step 3 Move the cursor to "LEVEL". Move the cursor horizontally to adjust the gain with use of the right or left button. Notes: · Change in the level of "AGC MAX" causes change in the level of the input signal that enables electronic sensitivity enhancement when "SENS UP" is set to AUTO and also change in the level of the input signal that activates black-andwhite mode. · If noise is undesirable, adjust the level of "AGC MAX". 29 5. Electronic sensitivity enhancement setting [SENS UP] Use of the electronic sensitivity enhancement function increases the quantity of light stored on the CCD, and accordingly the image becomes brighter. The magnification is unchanged for selection of FIX, and the magnification is changeable in accordance with the illuminance of a subject for selection of AUTO. The magnification of the electronic sensitivity is selectable from the following. OFF (default)/X2 AUTO/X4 AUTO/X6 AUTO/X10 AUTO/X16 AUTO/X32 AUTO/X2 FIX/ X4 FIX/X6 FIX/X10 FIX/X16 FIX/X32 FIX/X64 FIX/X128 FIX Notes: · When the magnification of "SENS UP" is increased, the screen becomes coarser, more whitish, or more flawed. · The status display of the system device does not show "X64 FIX" and "X128 FIX" of "SENS UP". In such cases, "X32 FIX" is shown. · If the controller, WV-CU254 or WV-CU204 is used, SW LED and the status of "SENS UP" are not correctly displayed. 30 6. Synchronization setting [SYNC] This unit supports the following 5 types of synchronization methods, and one of the following is selected. The order of descriptions below indicates the order of priorities. [. . . ] However, the data of the registered pixel compensation points is not cleared. Serial number viewing [SER. NO. ] The serial number of this unit appears. 49 Language Selection [LANGUAGE SETUP] A language for the setup menu is selected from the following: The language selection is performed on the "LANGUAGE SETUP" screen through the top screen. JAPANESE/ENGLISH (Default)/FRANÇAIS/ESPAÑOL/DEUTSCH/ITALIANO/êìëëäàâ **LANGUAGE SETUP** LANGUAGE ENGLISH SET RET TOP END To change the language to be used, use the right or left button to select the target language, move the cursor to "SET", and press the setting button. Notes: · When the language is changed, the specified camera title is cleared. · Only when Japanese is selected, katakana characters can be used for the camera title. 50 Shortcut Operation Use of a system controller with the "camera function" button allows users to perform the shortcut settings with use of the numeric keypad and camera function button. [. . . ]