User manual PANASONIC WV-CLR830

[. . . ] q Mount the lens by turning it clockwise on the lens mount of the camera. w Connect the lens cable to the ALC Lens Connector on the side of the camera. Pick-up Device: Scanning Area: Synchronization: Scanning System: Scanning: Horizontal: Vertical: Horizontal Resolution: Video Output: Signal-to-Noise Ratio: Electronic Light Control: Minimum Illumination: Focus Fixing Screw cs B. WV-CLR830 (12 V DC) Connect the power cord to the DC 12 V IN terminal on the rear panel of the WV-CLR830. Operating Instructions Model Nos. (Lens Option) WV-CP240EX WV-CLR830 WV-CP244EX 3TR004221AAA Printed in China Caution: To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007) for the DC 12 V or AC 24 V Input Terminal. @! MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS 12 V DC (10. 5 V - 16 V) Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. <WV-CP240EX> Resistance of copper wire [at 20 °C {68 °F}] w Copper wire size (AWG) Resistance /m Resistance /ft #24 (0. 22 mm2) 0. 078 0. 026 #22 (0. 33 mm2) 0. 050 0. 017 #20 (0. 52 mm2) 0. 03. [. . . ] The power cord is the main power disconnect for all units. q ALC Lens Connector Supplies power and control signals to an auto iris lens (not supplied). w Flange-back Adjusting Ring This ring adjusts the back-focal distance or picture focus. Rotate this ring clockwise for a C-mount lens or counterclockwise for a CSmount lens. e Lens (option) r Mount Adapter The camera mounting screw hole is for mounting the camera onto a mounting bracket. The camera is originally designed to be mounted from the bottom, however, a topmounting type is also available. To mount from the top, remove the mount adapter from the bottom of the camera by removing two fixing screws. Attach the mount adapter to the top as shown in the diagram, then mount the camera on the mounting bracket. Make sure that two original screws are used when mounting the mount adapter; longer type screws may damage inner components, too shorter type screws may cause the camera drop. t Focus Fixing Screw ON: Select this mode when a strong light such as a spotlight is in the background. !1 Detail/Aperture Level Selector [SHARP, SOFT] The detail/aperture level can be selected with this selector. Set it to the desired position while observing the picture on the monitor. o Synchronization Mode Selector [INT, LL] (only for WV-CP240EX and WVCP244EX) Selects the camera synchronization mode as either internal sync mode (INT) or line-lock mode (LL). !0 Back Light Compensation Mode Selector [BLC ON, OFF] Lets you select the mode according to the position of the object and light conditions on the screen. PRECAUTIONS 1. Do not attempt to disassemble the camera. To prevent electric shock, do not remove screws or covers. There are no user serviceable parts inside. Ask a qualified service personnel for servicing. The camera could be damaged by improper handling or storage. Do not expose the camera to rain or moisture, or try to operate it in wet areas. This product is designed for indoor use or locations where it is protected from rain and moisture. Turn the power off immediately and ask a qualified service personnel for servicing. Moisture can damage the camera and also create the danger of electric shock. Cautions: · Connect to 12 V DC (10. 5 V-16 V) or 24 V AC (19. 5 V-28 V) class 2 power supply only. [. . . ] Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. <WV-CLR830> DC 12V IN ALC BLC ON VIDEO SHARP ALC BLC ON VIDEO SHARP DC VIDEO OUT DC ELC SOFT OFF ELC SOFT Camera Mounting Screw Holes OFF Fixing Screws L standard = Mount Adapter L minimum = L maximum = VA - 12 0. 42 x R VA - 16 0. 42 x R VA - 10. 5 0. 42 x R (meters) (meters) (meters) C. WV-CP244EX (24 V AC 60 Hz) Connect the power cable to the AC 24 V IN terminal on the rear panel of the WVCP244EX. AC 24V IN GND C-mount: Less than 13 mm {1/2"} CS-mount: Less than 8 mm {5/16"} 1 2 24 V AC, 60 Hz (19. 5 V - 28 V) Recommended wire gauge sizes for 24 V AC line Copper wire size (AWG) Length of Cable (Approx. ) (m) (ft) #24 #22 #20 #18 (0. 22 mm2) (0. 33 mm2) (0. 52 mm2) (0. 83 mm2) 95 314 150 495 255 842 425 1 403 Caution: To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007) for the DC 12 V or AC 24 V Input Terminal. Video Cable 1. [. . . ]