User manual PANASONIC WV-CM1000

[. . . ] The wire which is coloured brown must be connected to the terminal in the plug which is marked with the letter L or coloured red. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK), NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is interned to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. The serial number of this product may be found on the top of the unit. [. . . ] Move the cursor to END, then to the item(s) you want to change. -17- ** CAM SET UP ** CAMERA ID OFF ALC/ELC ALC SHUTTER --AGC ON SYNC INT WHITE BAL ATW LENS DRIVE DC END SET UP DISABLE ** CAM SET UP ** CAMERA ID OFF ALC/ELC ALC SHUTTER --AGC ON SYNC INT WHITE BAL ATW LENS DRIVE DC END SET UP ENABLE Important Notice: When the cursor is moved to END and the CAM SET UP menu closed after changing the parameters, the new values are stored in the EEPROM (Electric Erasable and Programmable Read Only Memory). These values remain valid until new values are stored, even if the power of the camera is off. · Editing the SPECIAL menu To edit the SPECIAL menu (change settings), proceed as for editing the CAM SET UP menu above. Move the cursor to END after the words SET UP ENABLE appear. Then press and simultaneously for 2 seconds or longer. The SPECIAL menu appears on the monitor. Select the item to be changed and change the setting as described for the CAM SET UP menu. ** SPECIAL ** CHROMA GAIN AP GAIN PEDESTAL CAMERA RESET RET END . . . . I. . . . + PUSH SW -18- SETTING PROCEDURES 1. Camera Identification (CAMERA ID) Setting You can use the camera identification (CAMERA ID) to assign a name to the camera. The camera ID consists of up to 16 alphanumeric characters. You can select whether to have the camera ID displayed on the monitor screen or not. Pointer ** CAM SET UP ** CAMERA ID OFF ALC/ELC ALC SHUTTER --AGC ON SYNC INT WHITE BAL ATW LENS DRIVE DC END SET UP ENABLE Character Cursor 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ (). , '":;&#!?= +-*/%$ÄÜÖÆÑÅ SPACE POSI RET END RESET . . . . . . . . . . . . . . . . Character Area Command Editing Area CAMERA ID menu 3. Move the cursor to the character you want to change by pressing / / / . Move the cursor to the ALC/ELC parameter. Select ALC or ELC. WV-CM1000 ** CAM SET UP ** CAMERA ID OFF ALC/ELC ALC SHUTTER --AGC ON SYNC INT WHITE BAL ATW LENS DRIVE DC 2-1. ALC Mode with SUPER-D ON Super Dynamic Function (SUPER-D) The important object in a scene is usually placed in the centre of the monitor's screen. In SUPER-D mode, more photometric weight is given to the centre of the screen (where the important object is located) than to the edge of the picture (where a bright backlight would most likely be located). You can use the SUPER-D function if you select ALC. It eliminates interference by strong background lighting which makes the camera picture dark, such as a spotlight. ** ALC CONT ** BACK LIGHT COMP SUPER-D OFF MASK SET LEVEL RET END . . . I. . . . . + END ** ALC CONT ** BACK LIGHT COMP SUPER-D ** CAM SET UP ** CAMERA ID OFF ALC/ELC ALC SHUTTER --AGC ON SYNC INT WHITE BAL ATW LENS DRIVE DC END SET UP ENABLE LEVEL RET 1. Press after selecting ALC, the ALC CONT menu appears. Move the cursor to the SUPER-D parameter and select ON. 3. If you want to adjust the video output level, move the cursor to the "I" position. Adjust to the desired level by pressing or . [. . . ] To set MASK SET, proceed as described in steps 1 to 4 of "ALC mode with SUPER-D OFF and ELC mode" on page 22. Press or to obtain the optimum amount of red gain. Press or to obtain the optimum amount of blue gain. Note: When you need to set MASK SET, re-adjust to obtain the optimum amount of red and blue gain. 7. [. . . ]