User manual PANASONIC WV-CM146

[. . . ] Colour Monitor WV-CM146 Before attempting to connect or operate this product, please read these instructions completely ENGLISH VERSION We declare under our sole responsibility that the product to which this declaration relates is in conformity with the standards or other normative documents following the provisions of Directives EEC/73/23 and EEC/89/336. Noi dichiariamo sotto nostra esclusiva responsabilità che il prodotto a cui si riferisce la presente dichiarazione risulta conforme ai seguenti standard o altri documenti normativi conformi alle disposizioni delle direttive CEE/73/23 e CEE/89/336. Wij verklaren als enige aansprakelijke, dat het product waarop deze verklaring betrekking heeft, voldoet aan de volgende normen of andere normatiefve dokumenten, overeenkomstig de bepalingen van Richtlijnen 73/23/EEC en 89/336/EEC. Vi erklærer os eneansvarlige for, at dette produkt, som denne deklaration omhandler, er i overensstemmelse med den følgende standarder eller andre normative dokumenter i følge bestemmelserne i direktivene 73/23/EEC og 89/336/EEC. [. . . ] Press the Down switch (C). 0123456789:;ABCDEFGHIJKLMN OPQRSTUVWXYZÄÜÖÆÑÅØ"#'() + , - . (blank) ** SET UP MENU ** CAMERA ID 1. 34. . 7. 1 CAMERA AUDIO SELECT 1 TIMING SELECT INT SEQ TIME ADJ 1SEC PAGE SEQ 2SEC ALARM REC MODE FRAME ALARM TIME ADJ 10SEC BZ AUTO RESET OFF BRIGHT COMP 12. . 5. . 8 END SET UP ENABLE Press the Setup Switch. Press the SET UP switch. Characters can be selected using the Up (D) or Down switch (C). Column can be selected using the Left (A) or Right switch (B). After selecting them, press the SET UP switch. To select "CAMERA ID" of other camera, press the Left (A) or Right switch (B). 2. Audio Selection (AUDIO SELECT) ** SET UP MENU ** CAMERA ID 1. 34. . 7. 1 CAMERA AUDIO SELECT 1 TIMING SELECT INT SEQ TIME ADJ 1SEC PAGE SEQ 2SEC ALARM REC MODE FRAME ALARM TIME ADJ 10SEC BZ AUTO RESET OFF BRIGHT COMP 12. . 5. . 8 END SET UP ENABLE ** SET UP MENU ** CAMERA ID 1. 34. . 7. 1 CAMERA AUDIO SELECT 1 TIMING SELECT INT SEQ TIME ADJ 1SEC PAGE SEQ 2SEC ALARM REC MODE FRAME ALARM TIME ADJ 10SEC BZ AUTO RESET OFF BRIGHT COMP 12. . 5. . 8 END SET UP ENABLE After completing the selection, After completing Switch. the selection, press the Setup press the SET UP switch. ** SET UP MENU ** CAMERA ID 1. 34. . 7. 1 CAMERA AUDIO SELECT 1 TIMING SELECT INT SEQ TIME ADJ 1SEC PAGE SEQ 2SEC ALARM REC MODE FRAME ALARM TIME ADJ 10SEC BZ AUTO RESET OFF BRIGHT COMP 12. . 5. . 8 END SET UP ENABLE Press the Right Switch (B). Move the cursor to "AUDIO SELECT. " Select "SEQ" (sequential) or "1, 2, 3, 4" (fixed) using the Left (A) or Right switch (B). In "SEQ, " the audio signal is also switched according to channel switching. In "1, 2, 3, 4" (fixed, ) the audio signal is fixed to the selected channel. Note: During the fixed channel is selected, the audio of the selected channel changes to the alarmed channel if the alarm signal is received. The following table shows the audio sequential time when SEQ is selected for AUDIO SELECT. TIMING SELECT MONITOR MODE INT EXT ** SET UP MENU ** CAMERA ID 1. 34. . 7. 2 CAMERA AUDIO SELECT 1 TIMING SELECT INT SEQ TIME ADJ 1SEC PAGE SEQ 2SEC ALARM REC MODE FRAME ALARM TIME ADJ 10SEC BZ AUTO RESET OFF BRIGHT COMP 12. . 5. . 8 END SET UP ENABLE QUAD/SPOT Picture to be displayed: Picture to be displayed: changes frame by frame. changes with the timing you set on the time lapse VTR. Audio output: can be Audio output: changes selected from approx. Picture to be displayed: can be selected from approx. Picture to be displayed: changes at the time set on the time lapse VTR. SEQ/VTR Audio output: changes Audio output: changes at with the same time as the the time set on the time picture. [. . . ] Connect the TIMING SELECT IN connector of the monitor to the CAMERA SW OUT connector of the time lapse VTR with an RCA cable. Connect the AUDIO IN connector of the monitor to the AUDIO OUT connector of the time lapse VTR, and the AUDIO OUT connector of the monitor to the AUDIO IN connector of the time lapse VTR with an RCA cable. Important Notices: · Set TIMING SELECT to EXT on SET UP MENU and connect the TIMING SELECT IN connector of the monitor to the CAMERA SW OUT connector of the time lapse VTR with an RCA cable to record by the time lapse VTR. · Set the alarm recording mode of the time lapse VTR to 2H ( 2 hours. ) · When you record in linear mode (L12H, L18H, L24H) pay attention to the following; 1. [. . . ]