User manual PANASONIC WV-CM1480

[. . . ] Operating Instructions Model No. POWER ON OFF STANDBY INPUT SELECT MENU AUDIO Video Monito r WV -CM 2080 Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. ESPAÑOL FRANÇAIS DEUTSCH WV-CM2080 WV-CM1780 WV-CM1480 ENGLISH Colour Monitor We declare under our sole responsibility that the product to which this declaration relates is in conformity with the standards or other normative documents following the provisions of Directives EEC/ 73/23 and EEC/89/336. Noi dichiariamo sotto nostra esclusiva responsabilità che il prodotto a cui si riferisce la presente dichiarazione risulta conforme ai seguenti standard o altri documenti normativi conformi alle disposizioni delle direttive CEE/73/23 e CEE/89/336. Wij verklaren als enige aansprakelijke, dat het product waarop deze verklaring betrekking heeft, voldoet aan de volgende normen of andere normatieve documenten, overeenkomstig de bepalingen van Richtlijnen 73/23/EEC en 89/336/EEC. Vi erklærer os eneansvarlige for, at dette produkt, som denne deklaration omhandler, er i overensstemmelse med standarder eller andre normative dokumenter i følge bestemmelserne i direktivene 73/23/EEC og 89/336/EEC. Vi deklarerar härmed värt fulla ansvar för att den produkt till vilken denna deklaration hänvisar är i överensstämmelse med standarddokument, eller andra normativa dokument som framställs i EECdirektiv nr. [. . . ] Place the rack mounting brackets supplied onto the rear of the monitor and tighten with the eight supplied screws (M4 x 10). · Monitoring the Playback audio Connect the audio output of the VTR to the AUDIO IN A or B connector on the monitor with an audio cable. s Multiple Monitor Connection To monitor the same video on multiple monitors, connect the VIDEO OUT A or B connector on the monitor to the VIDEO IN connector of the other monitor with a coaxial cable. Up to 10 monitors in total can be connected in series before signal loss occurs. Total cable length should not exceed 150 meters (500 feet). (1 650 ft) (1 980 ft) (2 640 ft) s Connection with the VTR · Recording on the VTR Connect the VIDEO OUT A or B connector on the monitor to the video input of the VTR with a coaxial cable. Connect the AUDIO OUT A or B connector on the monitor to the audio input of the VTR with an audio cable, if applicable. 8 s Connection with the System Controller If the optional 6-conductor cable assembly is used, simply plug one end of the cable into the DATA port of the Monitor and the other end into the DATA port on the System Controller. If you use cables assembled from locally procured materials, it is important that only high quality, data grade cable, suitable for RS-485 communication (shielded 4-wire twisted pair cable), BELDEN 9406 or equivalent, is used. Lower grade cable will result in unstable operation of the system. DATA DATA RA RB ON OFF TERMINATION ON OFF TERMINATION TA G TA TB RA RB G N N D D To the System Controller System Controller WV-CU PROGRAM TB 360 q Setting the Termination Set the Termination Selector located on the rear of the monitor according to your requirements. OFF: Data is sent to other equipment. s Connection between two or more colour monitors and a device compatible with Panasonic Security Data mode In case of connecting multiple devices compatible with the Panasonic Security Data mode, connect the unit in a daisy-chain configuration as shown below. The allowable connecting devices are up to 16 in a system. The maximum allowable cable length of the system is approximately 500 m (1 650 ft). Termination: OFF FOCUS STANDBY ON STANDBY OFF G Termination: OFF FOCUS STANDBY ON STANDBY OFF G B IN AUDIO A IN B IN S-VIDEO VIDEO A IN B IN AUDIO A IN B IN S-VIDEO VIDEO A IN DATA DATA Termination: ON AC IN ON OFF TERMINATION OUT OUT IN OUT OUT AC IN ON OFF TERMINATION OUT OUT IN OUT OUT DATA Device compatible with PS. Data mode Modular cable (Supplied: WV-CU360) Termination: ON System Controller WV-CU PROGRAM To the Data port (optional) 360 System Controller compatible with PS. Data mode s Connection to the Standby On/Off Terminal Connecting an external device to the STANDBY ON/OFF Terminal on the rear of the monitor enables control of the monitor display by input from that device, both in normal and standby display mode. Shown below is an example of how to use this function. STANDBY ON STANDBY OFF G · STANDBY ON input Pulse +5 V DC · STANDBY OFF input Non-voltage contact or open collector output 0. 2 V 5V 0. 2 V Hi-Z Alarm Output Alarm Reset Output VL VH VL Note: To set up this function, refer to STANDBY ON in the Display Setting menu. 9 SETUP PROCEDURES This monitor offers various onscreen menus for setting user preferences. In the COMMUNICATION SETUP Menu, you can set the parameters for communication between the System Controllers and the Monitors. s Setup Menu As shown below, the Setup Menu has seven main submenus. One of these, CAM CONFIG, is further divided into additional submenus. After selecting the Setup Menu on the monitor screen, move the cursor to SETUP DISABLE with the C or D button, then press the - or + button. Display of SETUP ENABLE in the Setup menu indicates that setup is enabled. s Displaying the Setup Menu To display the Setup Menu, follow the procedure shown below. Confirm that the cameras and peripherals are connected correctly and securely. Turn the power of the monitor on by pressing the POWER button. Press the MENU button for 5 seconds or more. At first the Display Setting menu described on page 12 appears, and then the COMMUNICATION SETUP menu shown below. COMMUNICATION SETUP UNIT ADDRESS 1 CAM CONFIG BAUD RATE 9600 DATA BIT 8 PARITY CHECK NONE STOP BIT 1 WAIT TIME OFF SETUP ENABLE COMMUNICATION SETUP UNIT ADDRESS 1 CAM CONFIG BAUD RATE 9600 DATA BIT 8 PARITY CHECK NONE STOP BIT 1 WAIT TIME OFF SETUP DISABLE The following buttons are available in this Setup menu. 2. Move the cursor to the desired item with the C or D button. Select the desired item parameter with the - or + button. Press the MENU button to store the settings and return to normal viewing. q Unit Address (UNIT ADDRESS) C: Moves the cursor down. [. . . ] To set up this function, refer to STANDBY ON in the Display Setting menu. s To Reset to the Factory Default Settings If you are not sure about the settings you made and want to return to the factory default settings, follow the procedure shown below. Turn off the monitor by pressing the POWER button. Turn on the monitor by pressing the POWER button while holding down the MENU and + buttons. All settings in the Display Setting and the Setup menu are reset to the factory default settings. 14 OPERATING PROCEDURES (with the System Controller) For the following procedure, the WV-CM2080, WV-CM1780 or WV-CM1480 needs to be set up first from the Setup menu. [. . . ]