User manual PANASONIC WV-CP120

[. . . ] Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämä ilmoitus koskee, noudattaa seuraavia standardeja tai muita ohjeellisia asiakirjoja, jotka noudattavat direktiivin 89/336/EEC. Vi erklærer oss alene ansvarlige for at produktet som denne erklæringen gjelder for, er i overensstemmelse med følgende normer eller andre normgivende dokumenter som fælger bestemmelsene i direktiv 89/336/EEC. CONTENTS PREFACE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 FEATURES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 PRECAUTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] w Flange-back Adjusting Ring This ring is used to adjust the back focal length or picture focus by rotating it. e Video Output jack (VIDEO OUT) This jack is used to adjust the angular field of view or focus while observing the picture on the monitor. r Camera Mounting Screw Hole This screw hole (1/4" - 20) is used to mount the camera onto a mounting bracket or a tripod. t Auto Iris Lens Connector This 4-pin connector supplies power and the DC control signal to the auto iris lens. y Volume Control (VOLUME, MIN/MAX) The volume control is preset to centre position at the factory. Adjust it to prevent howling. u Video level Control (VIDEO LEVEL, L/H) This control adjusts the level of auto iris control when the ALC/ELC Switch 1!1 is set to ALC position, or the level of electronic light control when the ALC/ELC switch is set to ELC position. i ATW Balance Control (ATW BALANCE, R/B) This control adjusts the red and blue colour balance. It is preset to centre position which usually provides accurate colour reproduction. o Power Indicator !0 Camera Output Connector This connector is used to connect a coaxial cable to the CAMERA INPUT of the specified monitor or camera drive unit, to receive DC power and vertical drive pulse, and supply the audio and video output of the camera. !1 ALC/ELC Switch (ALC/ELC) This switch is used to choose the lens as follows. ALC: Choose this position when using an auto iris lens. ELC: Choose this position when using a fixed or manual iris lens. -5- !2 Detail level Switch (SOFT/SHARP) The detail/aperture level can be chosen by this switch. Choose the desired position while observing the picture on the monitor. When a Quad System is connected to this camera, set this switch to SOFT position. !3 BLC ON/OFF Switch (BLC, ON/OFF) When backlight affects the picture, set this switch to ON position for a clearer picture. !4 Microphone Switch (MIC, ON/OFF) Set this switch to ON or OFF as needed. ELC (Electronic Light Control) Function In this mode a continuously variable electronic shutter is employed to automatically control the exposure times in the CCD Image Sensor according to the incoming light level. Under bright conditions such as outdoors, use an ALC type lens as the ELC control range is not wide enough under such conditions. Under certain unique lighting conditions, the following may appear : · Strong smear and/or blooming on highlight objects such as spot lights or windows. · Noticeable flicker in the picture and/or colour rendition variations. · Periodic variance of white balance Should these phenomena occur, use an ALC lens. When shooting in the ELC mode with a fixed iris lens, the depth of field of the image may be less than that obtained with an ALC lens. Depth of field varies inversely with the iris opening. [. . . ] While viewing the monitor picture, loosen the angular control screw slightly. Adjust the camera's angle to the desired position, and then tighten the screw firmly. 164 (6-7/16) 2-5 (2-3/16) Angular Control Screw Cautions on installation Use wood screws with the camera mounting bracket that are suitable for Installation into a wood base of appropriate dimensions and strenght. For installation in a material other than wood, refer servicing to qualified service personnel. -17- PREVENTION OF BLOOMING AND SMEAR When the camera is faced toward spotlights or other bright lights and light reflecting objects, smear or blooming may appear. Therefore, the camera should be operated carefully in the vicinity of extremely bright objects to avoid smear or blooming. , , , , , , Smear Bright object -18- SPECIFICATIONS Pick-up Device: Scanning Area: Synchronization: Scanning System: Scanning: Horizontal: Vertical: Horizontal Resolution: Video Output: Signal-to-Noise Ratio: Electronic Light Control: Minimum Illumination: Gain Control: White Balance: Detail: BLC: Audio: Lens Mount: Ambient Operating Temperature: Ambient Operating Humidity: Power Source: Interline Transfer CCD, 512 (H) x 582 (V) pixels. [. . . ]