User manual PANASONIC WV-CP230P

[. . . ] Serial No. WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. IMPORTANT The wires in this mains lead are coloured in accordance with the following code. Green-and-yellow: Earth Blue: Neutral Brown: Live As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows. The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol I or coloured green or green-and-yellow. The wire which is coloured blue must be connected to the terminal in the plug which is marked with the letter N or coloured black. [. . . ] ATW (Automatic Tracing White Balance) System is incorporated into the WV-CP230P series. This system has a colour temperature sensor for accurate detection of light source colour temperatures projected onto objects without affect of ambient temperatures and light intensity according to the angle of incident. In addition, ability to shoot indoor scenes with a fixed iris lens by use of Electronic Light Control (ELC) function. The built-in AGC (Automatic Gain Control) allows to obtain a clear picture under the low light condition. FEATURES · Minimum illumination of 0. 5 lx at F0. 75 [equivalent 1. 5 lx at F1. 4] and Signal-to-Noise ratio of 46 dB by employing a 1/3 inch interline transfer CCD image sensor with 512 (H) x 582 (V) pixels. · 330 lines of horizontal resolution · Optional C-mount lens can be used together with optional Lens Mount Converter (C-mount adaptor) WV-AD20. · Selectable internal sync (INT), line-locked sync (LL) or Multiplexed Vertical Drive (VD2) for WVCP220/WV-CP224. · Automatic Gain Control (AGC) (+15dB) and Automatic Tracing White Balance Control (ATW) are built-in. -3- PRECAUTIONS · Do not attempt to disassemble the camera. To prevent electric shock, do not remove screws or cover. There are no user-serviceable parts inside. Refer servicing to qualified service personnel. The camera could be damaged by improper handling or storage. (9) Detail level Selection Switch (SOFT/SHARP) The detail/aperture level can be selected by this switch. Set the switch to the desired position while observing the picture on the monitor. Note: Usually set this switch to SHARP position. When Quad System is connected to this camera, set this switch to SOFT position. -6- (10) DC 12V In Terminal (DC 12V IN) This terminal accepts 12V DC power source (10. 5V - 16V). (11) AC 24V In Terminal (AC 24V IN) This terminal accepts 24V AC power source (19. 5V - 28V). Be sure to connect grounding lead to the GND terminal. -7- CONNECTIONS A. Connect the AC Power Cord to a electrical outlet of 220 - 240V AC 50 Hz. · Calculation method of maximum cable length between camera and power supply. 10. 5V DC VA - (R x 0. 42 x L) 16V DC L : Cable length (m) R : Resistance of copper wire (/m) VA : DC output voltage of power supply unit L standard = L minimum = L maximum = VA - 12 0. 42 x R VA - 16 0. 42 x R VA - 10. 5 0. 42 x R (m) (m) (m) B. Connect the power cable to the DC 12V In Terminal on the rear panel of the camera. DC 12V IN - + 12V DC (10. 5 V - 16 V) Resistance of copper wire (at 20°C) Copper wire size (AWG) Resistance /m Resistance /ft #24 (0. 22mm2) 0. 078 0. 257 #22 (0. 33mm2) 0. 050 0. 165 #20 (0. 52mm2) 0. 030 0. 099 #18 (0. 83mm2) 0. 018 0. 059 -8- C. A power supply of 24V AC 50 Hz is required. Connect the power cable to the AC 24V In Terminal on the rear panel of the camera. Video Cable 1. [. . . ] Attach the mount adaptor to the top as shown in the diagram, then mount the camera on the mounting bracket. Make sure that two original screws are used when mounting the mount adaptor; longer type screws may damage inner components. <Mounting from the top> Fixing Screws Mount Adaptor <Mounting from the bottom> -17- FOCUS OR FLANGE-BACK ADJUSTMENT The following adjustment should be made by qualified service personnel or system installers. Loosen screws on the flange-back adjusting ring. PREVENTION OF BLOOMING AND SMEAR When the camera is faced toward spot light or other bright lights and light reflecting objects, smear or blooming may appear. Therefore, the camera should be operated carefully in the vicinity of extremely bright objects to avoid smear or blooming. Flange-back Adjusting Ring , , , , , , Smear Bright object 2. [. . . ]