User manual PANASONIC WV-CP234

[. . . ] Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämä ilmoitus koskee, noudattaa seuraavia standardeja tai muita ohjeellisia asiakirjoja, jotka noudattavat direktiivien 73/23/EEC ja 89/ 336/EE. Vi erklærer oss alene ansvarlige for at produktet som denne erklæringen gjelder for, er i overensstemmelse med følgende normer eller andre normgivende dokumenter som følger bestemmelsene i direktivene 73/23/EEC og 89/336/EEC. For U. K. FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY. This appliance is supplied with a moulded three pin mains plug for your safety and convenience. [. . . ] !3 Data Ports (DATA) These ports are used to exchange control data with the System Controller in Panasonic Security Data mode. !4 Data Termination Selector (TERMINATION ON/OFF) This selector is used to enable termination of the monitor's data port. t Menu Button (MENU) Pressing this button opens the Display Setting menu for changing the monitor's display settings. Pressing this button for 5 seconds or more opens the COMMUNICATION SETUP menu. 5 !5 Standby Control Terminal (STANDBY ON/STANDBY OFF/G) This terminal accepts input from an outboard device to control the standby mode. It operates as follows: STANDBY ON: Establishes the specified standby mode. STANDBY OFF: Releases standby mode (normal display). !6 Audio Input Connectors (AUDIO IN A/B) For audio input from an outboard device !7 Audio Output Connectors (AUDIO OUT A/B) The audio input signal connected to the Audio Input Connector is looped through to this connector. !8 S-Video Input Connector (S-VIDEO IN) For input of S-video signal from an outboard device. !9 Video Input Connectors (VIDEO IN A/B) For input of composite video signal from an outboard device. @0 Video Output Connectors (VIDEO OUT A/B) The video input signal connected to the Video Input Connector is looped through to this connector and terminated automatically. @1 AC Inlet Socket (AC IN) Plug the power cord (supplied as a standard accessory) into this socket and connect it to an AC outlet. 6 INSTALLATION The installation described below should be made by qualified service personnel or system installers. s Mounting into the Rack for WV-CM2080 The monitor can be mounted into the rack as described below. Place the rack mounting brackets supplied onto the rear of the monitor and tighten with the eight supplied screws (M4 x 10). Select the desired item parameter with the - or + button. Press the MENU button to store the settings and return to normal viewing. q Unit Address (UNIT ADDRESS) C: Moves the cursor down. To finalize the settings and return to normal viewing, press the MENU button. This item lets you set the unit address of the monitor in the system for RS-485 communication. Move the cursor to the UNIT ADDRESS parameter with the C or D button. COMMUNICATION SETUP UNIT ADDRESS 1 CAM CONFIG BAUD RATE 9600 DATA BIT 8 PARITY CHECK NONE STOP BIT 1 WAIT TIME OFF SETUP ENABLE 2. Select the unit address number to be used for RS-485 communication with the - or + button. Select a parameter value between 1 and 99. The factory default setting is 1. 10 q Camera Configuration (CAM CONFIG) This item lets you set numbers for the input from system cameras for RS-485 communication. Move the cursor to CAM CONFIG with the C or D button, then press the - or + button. The CAMERA CONFIG menu shown below will appear on the monitor screen. q Baud Rate (BAUD RATE) This item lets you set the transmission speed for RS-485 communication. Move the cursor to the BAUD RATE parameter with the C or D button. [. . . ] MODE 1: Pictures are displayed with less brightness. MODE 2: Monitor blackout, i. e. , no picture is displayed. Notes: · Speaker (audio) output is disabled in the standby mode. · The Standby mode can be controlled by the input from the STANDBY ON/OFF terminal on the rear of the monitor. The input signal will toggle the mode selected in the Display Setting menu on and off. [. . . ]